船艇电站仿真与综合管理系统

论文介绍了船艇电站模拟器的组成和实时仿真功能,着重描述了多层次的图形管理系统及其仿真界面。课题将多媒体课件制作与模拟器有机地结合,涵盖了船舶主要电气设备的控制电路,既利于实践训练又便于原理的讲解,并在实践中取得了良好的效果。     

动态分频器技术

本文介绍了动态分频器的基本原理；详细叙述了动态分频器电路及其主要工艺技术；综述了国外动态分频器的发展动态。     

叠后高分辨率资料处理方法及应用效果

高分辨率勘探是一项系统工程，它由多个环节组成。甚至叠后高发辨率资料处理也是由多个环节组成。本文介绍的叠后高分辨率资料处理流程主要包括Ｌｐ模自适应预测统计反褶积，高频成分补偿，振幅补偿及有色成分校正。文中还就处理流程中各种方法的合理组合，各种方法自身参数的合理选取作了试验和探讨，最后给出了处理实例。     

合山电厂3个机组主厂房定向爆破拆除

介绍了广西合山电厂 1#～3# 机组主厂房定向爆破设计与施工.该工程不仅规模大、环境十分复杂、工期紧、难度高、风险性极强,最大特点是拆除发电设备与爆破同步进行施工.     

高频等参数感应(ВИКИЗ)测井技术应用

介绍了高频等参数感应的基本原理。以胜利油田比较典型的 3口井为例 ,详细分析了高频感应资料在划分薄夹层、确定储层流体饱和类型、评价储层电阻率空间分布等方面的应用。研究结果表明 ,高频感应具有极高的纵向分辨率和较好的径向探测特性 ,能够准确计算地层真电阻率、侵入带电阻率及侵入半径 ,通过与常规感应及薄层测井资料的对比 ,论证了高频等参数感应在测井技术应用上的优越性     

高能气体压裂联作技术进展

国内高能气体压裂增产技术已经由单一的有壳弹、无壳弹、液体药、可控脉冲等高能气体压裂,进展到与射孔、水力压裂、酸化、化学解堵等技术相联作的综合压裂阶段。分别对高能气体压裂与射孔、水力压裂和化学解堵等联作技术的基本原理、现场试验、作业效果等进行了介绍。高能气体压裂已发展成一种基本成熟的、综合性油气田增产改造新技术。     

A load dispatch method using fractional programming and semidefinite programming

This paper describes a load dispatch method which minimizes power cost—[fuel cost]/[electric output]—for a power system with thermal plants and energy storage facilities. The proposed method employs fractional programming to convert a minimization problem with fractional objective function to a series of quadratic minimization problems, and semidefinite programming to solve converted problems. The method provides the optimum time‐dependent power output/input and storage level of energy storage facilities as well as time‐dependent power output of thermal plants. The method has been applied to a power system with five thermal plants, two energy storage facilities of various performances, and five load demands. The optimum load scheme of four time mesh points is obtained for the thermal plants and energy storage facilities. The fractional programming successfully converges the optimal scheme through a few iterations. The semidefinite programming deals with a variable matrix of 164 dimensions, and 185 inequality constraints. © 2001 Scripta Technica, Electr Eng Jpn, 138(2): 49–58, 2002     

平面Z-型软磁铁氧体频率特性的研究

研究分析了Co2Z材料显微结构与磁性能的关系,在普通铁氧体工艺中引入预磁化处理方法,并适当控制二次再结晶现象,成功地研制出高性能的Co2Z型宽频材料,Z-型铁氧体材料的共振频率可达1.8GHz以上,截止频率在1GHz附近,起始磁导率在8-13之间,介电常数相对较低(ε'<30)。     

用瑞利波检验高喷防渗墙的施工质量及地层分布特征

本文阐述了瞬态多道瑞利波探测的原理和方法，并将其应用到大堤高喷防渗墙施工质量的检验中，取得一定成效，测试结果与测压管观测结果对比，相互吻合，为类似工程的质量检验提供了一种可采用的检测手段。     

Effect of crack-growth mechanism on the prediction of fracture load of adhesive joints

This paper presents observations regarding the cracking behavior of tensile-loaded structural adhesive joints. Experiments showed that fracture occurred by the development and propagation of a damage zone, rather than a single, sharp crack, and that the presence of the adhesive spew fillet did not affect the fracture load of the adhesive joints studied. For joints bonded with the mineral-filled epoxy Cybond 4523GB (American Cyanamid), there was approximately 5 mm of subcritical crack propagation prior to final fracture. Fracture-load predictions based on the initial uncracked geometry made in previous papers were unaffected by this small change in geometry. For joints bonded with the rubber-toughened epoxy Permabond ESP 310, approximately 50 mm of subcritical crack propagation was observed. It was again found that predictions made in previous papers on the basis of the initial geometry gave a good estimate of the final fracture load even though this subcritical crack propagation significantly altered the geometry, and thus the applied energy release rates. The effect of shear deformations of the adherends was also investigated, and it was found that shear deformations could be neglected in engineering calculations for joints subject to remote tensile loading.