桩帽处理对灌注桩高应变检测的影响

本文给出砼灌注桩高应变检测中桩帽的施工工艺 ,并讨论其对测试结果的影响。     

Yield Stress and Microstructure of Set Yogurt Made from High Hydrostatic Pressure-Treated Full Fat Milk

ABSTRACT: Set yogurts were prepared from fortified milk subjected to the following processes: (a) Thermal process (85C,°C,35 min), (b) High hydrostatic pressure process (193 or 676 MPa for 5 or 30 min), and (c) Nonprocessed milk (control). Yogurts from milk treated with 676 MPa for 30 min exhibited similar yield stress and water-holding capacity (WHC) to yogurts from heated milk. Transmission Electron Microscopy (TEM) micrographs exhibited small round casein micelle aggregates without appendages in yogurts from heated milk. Yogurts from milk treated with 193 MPa and untreated milk exhibited low yield stress, low WHC, and large clusters of coalesced micelles. Mechanisms for gel formation are discussed.     

用于千兆以太网基带铜缆接收器均衡的甚高频自适应 连续时间Gm-C 二阶带通滤波器的研究和设计

本文设计了用于千兆以太网基带铜缆接收器均衡的甚高频自适应连续时间Gm-C二阶带通滤波器。基于最陡梯度下降算法，带通滤波器的零点在57－340MHz的频率范围内可以自适应地调节，中心频率为1.278GHz。通过外接电阻伺服环路，滤波器中跨导转换器的跨导值不受工艺偏差和温度变化的影响，采用CSMC－HJ0.6μm CMOS工艺器件模型，用Cadence Spectres仿真器仿真了设计的自适应滤波器电路，仿真结果验证了设计原理和设计的电路。系统的最长学习时间为880个参考时钟周期。     

The Loss of Hydrophobic Polypeptides during Fermentation and Conditioning of High Gravity and Low Gravity Brewed Beer

The object of this study was to investigate the loss of hydrophobic polypeptides, which are important for foam quality and stability in finished beer. Loss of hydrophobic polypeptide due to fermenter foaming occurs during transfer of fermented wort since a gradient of hydrophobic polypeptides towards the surface is created during fermentation. Due to higher polyphenol levels in high gravity (20°Plato) wort, more hydrophobic polypeptides are lost due to cold break (cold trub) precipitation compared to low gravity (12°Plato) wort. Another important factor affecting the loss of hydrophobic polypeptides could be proteinase A activity during fermentation, especially in high gravity fermentation where the yeast is exposed the higher stress. During high gravity fermentation, where osmotic pressures are higher, ethanol levels become greater, and nitrogen‐carbohydrate ratios are lower, more proteinase A is released by the yeast. This release of proteinase A into fermenting wort could have implications for the foam stability of the finished product.     

一种在Kalman滤波中引入径向速度测量的新方法

研究在距离和径向速度测量噪声统计相关的情形下把径向速度测量引入Kalman滤波的新方法。分析了径向速度测量噪声与位置测量更新后状态滤波误差的统计相关性,根据Gauss-Markov定理导出了对应于径向速度测量的滤波方程由此而得到一种序贯滤波算法。两个不同的蒙特卡罗仿真表明,通过采用这一新算法引人径向速度测量,不仅可以大大提高状态估计的精度,而且其估计性能和计算效率优于传统的EKF。     

45钢表面超音速电弧喷涂Ti-Al涂层的组织与性能研究

采用自行开发研制的超音速电弧喷设备，在45钢表面制成了钛铝合金复合涂层。并利用金相显微镜、X射线衍射仪、扫描电镜、电子探针，对涂层的成分、相结构、显微组织及其结合强度、显微硬度进行了研究。结果表明，利用超音速电弧喷涂设备，可以在45钢表面形成 度高、孔隙率低，结合强度较好和硬度高的Ti-Al合金涂层。     

钢纤维喷射混凝土作为面板材料的可行性研究

钢纤维混凝土作为一种新型增强材料，以其较好的受力变形特性在水利水电，交通，海岸防护，港口及军事等诸多工程中得到了广泛的应用。针对混凝土面板堆石坝面板的受力变形特点，为改善水布垭面板堆石坝面板的受力条件，提高其防渗能力，同时方便施工，现提出采用钢纤维喷射混凝土作为水布垭面板堆石坝面板材料的新构想，并通过对钢纤维喷射混凝土的物理力学特性及堆石坝面板受力变形进行分析，为钢纤维喷射混凝土在水布垭面板堆石坝面板中的实际应用提出了建议方案。     

首钢外购焦炭质量恶化后的高炉生产实践

针对焦炭质量劣化的状况，高炉操作以活跃炉缸为主，从上下部调剂入手，采取疏导煤气、控制合理的实际风速和鼓风动能、缓解焦炭在高温区的粉化等措施，有效地改善了高炉的顺行状况，并逐步恢复高炉指标。     

连续生产型炉窑排烟温度合理性探讨

推导了热效率变化百分率和单产标准煤耗变化百分率的计算公式 ,通过计算说明了连续生产型炉窑依靠高效余热回收而实施高烟温生产操作 ,实际上是增加而不是减少燃料消耗 ,据此 ,指出“三高一低”理论的不完全正确和HTAC技术在此类炉窑上的不可用性。论述了连续生产型炉窑低烟温的合理性 ,并提出基于低烟温的“双高低”理论和“烟混型高温低氧燃烧法” ,促使连续生产型炉窑向高效节能环保方向发展     

Facile modifications of polyimide via chloromethylation: II. Synthesis and characterization of thermocurable transparent polyimide having methylene acrylate side groups

From chloromethylated polyimide, a useful starting material for modification of aromatic polyimides, a thermocurable transparent polyimide having acrylate side groups was prepared. In the presence of 1,8‐diazabicyclo[5,4,0]undec‐7‐ene, chloromethylated polyimide was esterified with acrylic acid to synthesize poly(imide methylene acrylate). The polymer was soluble in organic solvent, which makes it possible to prepare a planar film by spin coating. The polymer film became insoluble after thermal treatment at 230 °C for 30 min. Optical transparency of the film at 400 nm (for 1 µm thickness) was higher than 98 % and not affected by further heating at 230 °C for 250 min. Adhesion properties measured by the ASTM D3359‐B method ranged from 4B to 5B. Preliminary results of planarization testing showed a high degree of planarization (DOP) value (>0.53). These properties demonstrate that poly(imide methylene acrylate) could be utilized as a thermocurable transparent material in fabricating display devices such as TFT‐LCD. Copyright © 2004 Society of Chemical Industry