SYP增效剂用于褐铁矿烧结的试验研究

根据昆钢红河钢铁有限公司烧结以褐铁矿为主的原料特点，结合生产实践提出了添加SYP增效剂烧结的技术思路。在实验室烧结杯试验取得初步效果的基础上，组织了工业性试验，验证了SYP增效剂改善烧结生产技术经济指标的作用。SYP增效剂的使用，在一定程度上解决了褐铁矿烧结强度差、返矿量大的问题，为拓宽资源利用，降低成本奠定了良好的基础。     

承钢150 m2烧结机布料系统的改进

为了提高烧结料层的粒度偏析和透气性，降低边缘效应，改善布料质量，对承钢150m^2烧结机布料系统进行了改进，包括：布料矿槽容积和形状的改进；五辊改九辊；重新布置松料器；增加压料器和九辊拦板等。改进后，取得了满意的效果。     

烧结机台车侧密封装置的开发与应用

为了解决烧结机台车端部漏风问题,研制开发了烧结机台车侧密封装置。该装置由膜盒、膜片、阻尼阀、杠杆联动机构、密封杆、密封材料以及限位支撑套等构成,通过台车底部的负压吸动膜盒的膜片产生位移,使密封材料自动压紧覆盖住台车端部的漏风间隙。生产实践证明,烧结机台车端部漏风率大幅度降低,年效益达2100万元。     

二烧改造工程环保设备设计及特点

围绕二烧工程改造,介绍了该工程的环保设计原则,针对烧结生产中各工序的环境污染治理采取了一系列的措施,极大地改善了厂区环境,同时为类似的大型烧结机的环境保护和粉尘治理提供了有益的经验.     

Numerical Analysis of Coaxial Double Gate Schottky Barrier Carbon Nanotube Field Effect Transistors

Carbon nanotube field-effect transistors (CNTFETs) have been studied in recent years as a potential alternative to CMOS devices, because of the capability of ballistic transport. The ambipolar behavior of Schottky barrier CNTFETs limits the performance of these devices. A double gate design is proposed to suppress this behavior. In this structure the first gate located near the source contact controls carrier injection and the second gate located near the drain contact suppresses parasitic carrier injection. To avoid the ambipolar behavior it is necessary that the voltage of the second gate is higher or at least equal to the drain voltage. The behavior of these devices has been studied by solving the coupled Schrödinger-Poisson equation system. We investigated the effect of the second gate voltage on the performance of the device and finally the advantages and disadvantages of these options are discussed.     

Microstructure and abrasion wear behavior of Ni-based laser cladding alloy layer at high temperature

Ni-based alloy coating on 21-4-N heat-resistant steel was prepared using CO2 laser, and the high-temperature abrasion wear was tested. The microstructure of this cladding layer and its abrasion wear behavior at high temperature by changing compositions and temperatures were investigated by means of optical microscope and scanning electron microscope. Among the three compositions of cladding layer, i.e. Ni21 ＋20% WC＋0. 5 % CeO2, Ni25＋20 % WC＋0. 5 % CeO2 and Ni60 ＋ 20 % WC ＋ 0. 5 % CeO2, the experimental results show that Ni21 ＋ 20 % WC ＋ 0.5?O2 cladding layer is made up of finer grains, and presents the best abrasion wear behavior at high temperature. The wear pattern of laser cladding layer is mainly grain abrasion at lower temperature, and it would be changed to adhesive abrasion and oxide abrasion at higher temperature.     

尖晶石锂锰氧化物的电化学性能研究

以LiOH.H2O和Mn(CH3COO)2.2H2O为原料,用微波烧结和固相烧结相结合合成了尖晶石型Li4Mn5O12正极材料.XRD分析、DTA分析、循环伏安和充放电实验表明,先用300W的微波烧结30min,然后再用380℃后处理48 h可获得具有纯Li4Mn5O12物相的样品.该样品的初始放电容量为176mAh/g,40循环的放电容量为123 mAh/g.     

“三软”煤层炮采放顶煤工作面矿压规律研究

通过对红旗井中厚煤层炮采放顶煤工作面矿压观测分析,得出“三软”中厚煤层炮采放顶煤工作面的矿压显现特征,综合评价其支架的适应性与工作状态,为工作面支架选型提供依据,对同类条件下放顶煤工作面开采具有指导意义.     

Rheological behavior of continuous roll casting process of aluminum alloy

The rheological behavior of aluminum alloy and its influencing factors in physical simulation of continuous roll casting process were studied by using a Gleeble-1500 thermal-mechanical simulation tester with a set of special clamp system. The relationships between the flow stress and the strain rate in the deformation process of simulating roll casting experiment were obtained. The results show that four different characteristic stages exist in the temperature range of the whole rheological process. The first occurs when the temperature is higher than 600℃, which belongs to the creep deformation stage; the second occurs when the temperature lies in the range of 500 - 600℃, and it can be regarded as the high temperature and low stress level deformation stage; the third occurs when the temperature decreases to the range of 300 - 500℃, it is considered to be the middle stress level deformation stage; the last occurs when the temperature is less than 300℃ and the strain rate is less than 1.00 s^-1 , it belongs to middle stress level deformation stage. But when the strain rate is larger than 1.00 s^-1, it belongs to the high stress level deformation stage. And the relative constitutive models suitable for the four different stages of continuous roll casting process were established through multivariate linear regression analysis of the experimental data.     

The Densification of Cu／Ti System by Spark Plasma Sintering

In order to unclose the dynamics of SPS densification, a special sintering sample (Cul Ti wires compact) was designed. Characters of the shrinkage rates during sintering process and mierostructures of products fabrieated by the spark plasma sintering( SPS ) and hot-press .sintering were investigated. The experimental results reveal that a higher temperature field is formed at the connected area and conductive net of the compact. These high-temperature parts deformed more easily than other parts, which is believed to be the main cause of SPS fast densification, according to a hard-core and soft-hell material model.