用LG55冷轧管机轧制小直径不锈钢管孔型改进

介绍了ＬＧ５５冷轧管机使用Φ７～３２ｍｍ、Φ５０～３２ｍｍ孔型轧制小直径不锈钢管的工艺特点。试验表明，两种孔型可行，且Φ５７～３２ｍｍ孔型的综合使用效果更好。     

提高Cr12MoV钢冷作模具寿命的措施

从原材料改锻、预备热处理、淬火及回火、深冷处理、表面强化处理等方面分析介绍了提高Cr12MoV钢冷作模具寿命的一些方法和措施 ,并通过实例表明 ,采用这些方法和措施可较大幅度地提高模具寿命     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

Enabling factors toward production of nanostructured steel on an industrial scale

Utilizing the existing properties of steel, a modern technological society has been constructed. While there are over 25,000 worldwide equivalent steels based on manipulating the eutectoid transformation, there exist only a handful of commercial nanostructured steel alloys based on manipulating the more complex glass devitrification transformation. Thus, research on nanostructured steels is in its infancy, and many further developments are expected with the demonstrated promise of developing new combinations of superior properties. In this article, seven enabling metallurgical factors are presented that ultimately allow a variety of nanostructured steel products to be produced in an ever-increasing array of industrial processing techniques. Additionally, a case example of the formation of nanostructured steel are given showing how these factors can be harnessed on an industrial scale.     

DD—921钢铁常温发黑剂的研制和应用

研究了钢铁常温发黑过程的成膜机理,各组分之间的作用以及相互之间的影响,着重分析了常温发黑的优缺点,工艺控制参数以及经济性。     

Controlling the Cold Roll Forming Design Process

The cold roll forming process requires successive forming profiles to be determined and an appropriate number of profiled roll sets to be designed for the product to be rolled. This paper examines the design process and how one company has put in place a design-production control system that allows designs to be ranked in terms of quality and efficiency. In addition, consideration is given to the proportion of time given to each design task and how non-creative design activities can be automated.     

热压变形对灰口铸铁石墨形态的影响

研究了灰口铸铁(HTl50)在900℃大压下量塑性变形后石墨的分布形态，结果表明：随着压下量的增加，石墨片逐渐趋于平行分布；变形过程中发生了碳的回溶，同时伴随着石墨片的断裂；石墨片体积分数及片间距随压下量的增加而逐渐减少。     

关贸总协定与钢铁产品出口贸易的若干问题

探讨了我国恢复关贸总协定缔约国地位后，钢铁产品进出口贸易中的一些问题，分析了几家钢铁公司的进出口情况，指出马钢公司产品出口应注意的问题。     

汽车覆盖件成形过程数值模拟研究

本文介绍汽车覆盖件成形过程有限元模拟两个软件ＩＴＡＳ—３Ｄ和ＤＹＮＡＭＩＣ的最新研究成果，基本原理和有关接触搜索、摩擦和拉伸筋模型等关键技术。并有两个应用实例