热变形对多元合金耐磨铸铁组织和性能的影响

研究了热变形量对多元合金耐磨铸铁组织和冲击韧度的影响，结果表明，热变形能改变耐磨铸铁组织中共晶碳化物的形状与分布，促进颗粒状碳化物的析出，提高耐磨铸铁的冲击韧度。当该耐磨铸铁的热变形量为40％时，其冲击韧度最佳。     

一种Cr—Mn—Mo—B低碳低合金钢的热变形行为

利用ＴＨＥＲＭＣＭＡＳＴＯＲ－Ｚ热处理机对一种Ｃｒ－Ｍｎ－Ｍｏ－Ｂ钢的热变形行为进行了研究，绘制了真应力－应变曲线，得到了各变形工艺参数之间的定量关系，得出试验用钢的Ｑ值为３７３．７ｋｊ／ｍｏｌ。在此基础上给出了试验用钢的动态再结晶图，试验发现，试验用钢９００℃以上变形后，在奥氏体区冷过程中发生静态再结晶与晶粒长大，相变前晶粒尺寸与变形条件Ｚ的关系：ｄｒｅｃ＝２．８８×１０＾４×Ｚ＾－０．２０５。     

高炉铁水含硅量的混沌局部线性预测

对莱钢1号高炉(750 m3)、临钢6号高炉(380 m3)铁水含硅量([Si])进行了混沌局部线性预测.结果表明,两 座高炉[Si]的一步预测的命中率在[Si]±0.1％的范围内均达到80.0％以上,对莱钢1号高炉(b)类样本甚至达89.1％,且预 测精度在10-2数量级,对实际生产具有很好的指导作用.     

PHYSICAL SIMULATION OF INTERFACIAL CONDITIONS IN HOT FORMING OF STEELS

1.~nonNUInericalmodellingbythefiniteelement(FE)methodhasbecomeaneffectiveandeconomyicmeansforsimulatingmetalfoeingprocesses.However,accuratemodellingdemandsthecorrectdefinitionandinputsofthedataforthethermalandphysicalpIDPertiesoftheworkpieceandtoolmaterials,theboUndaryconditionsattheworkpiece--toolinterfaceandinotherareas,inadditiontoappropriatemeshgenerationandnumericalsolutions.Althoughmostofthematerialdataareavailable,thedataforinterfacialheattransferandfrictionconditions,Whichhavesubst…     

New inverse method for identification of constitutive parameters

A new inverse method by coupling iSIGHT and ABAQUS was proposed to determine the constitutive parameters of Al2O3sf/LY12 composite deforming at elevated temperature. It combined the merits of the f＇mite element simulation and optimization technique. The direct model was simulated with finite element code ABAQUS. The inverse problem associated with the identification of the constitutive parameters was expressed as a least square optimization problem. The direct simulation and the parameters optimization were implemented in iSIGHT integrated environment. The aim was to match the output of the direct simulation with the experiment data. The capability of the proposed inverse method was demonstrated through the identification of constitutive parameters of Al2O3sf/LY12 composite. The proposed new inverse method is also applicable to other parameters identification which is hardly determined through experiments or direct analytical method.     

Properties of Co-doped N-type FeSi2 processed by mechanical alloying

Iron-silicide was produced with a mechanical alloying process and consolidated through vacuum hot pressing. The as-milled powders were of metastable state and fully transformed into the ß-FeSi₂ phase through subsequent isothermal annealing. The as-consolidated iron silicides consisted of an untransformed mixture of α-Fe₂Si₅ and ?-FeSi phases and a partially transformed β-FeSi₂ phase was found in the low density compact. Isothermal annealing was carried out to induce transformation into a thermoelectric semiconducting β-FeSi₂ phase. The transformation behavior of the β-FeSi₂ was investigated utilizing DTA, SEM, and XRD analyses. Isothermal annealing at 830°C in vacuum led to a thermoelectric semiconducting β-FeSi₂ phase transformation, but some residual metallic α and ?-phases were unavoidable even after 96 hours of annealing. The iron silicide microstructures were investigated using SEM and TEM. The mechanical and thermoelectric properties of the β-FeSi₂ materials before and after isothermal annealing are characterized in this study.     

LD7铝合金热变形行为的实验研究

在G1eeble-1500热模拟试验机上对LD7铝合金试样在变形程度为60％，变形温度为360～480℃、变形速率为0．0l～1s^-1的条件下进行等温压缩试验，然后对其进行固溶处理。根据试验结果分析热变形参数对合金流动应力和固溶之后显微组织的影响，可以得到如下结论：LD7铝合金是动态回复型合金，合金的流动应力随温度的升高而降低，随应变速率的升高而升高；合金的晶粒尺寸随温度的升高而增大，随变形程度和变形速率的增大而减小。     

Monte-carlo modeling of grain growth in Zr equal channel angular pressed and recrystallized

Grain boundary character distribution in equal-channel-angular pressed Zr was studied. Using a die design of 90°/20° and an operation temperature of 350°C. The initial grain size of 20 μm was reduced to about 270 nm with 4 passes via route B_c. The grain growth kinetics of the recrystallized state was obtained by experiment and Monte-Carlo computer simulation, respectively, which showed good agreement. Based on kinetics and morphological characteristics, it was concluded that the grain coarsening mechanism was governed by normal grain growth. No sign of abnormal grain growth was detected either in the experiment or in simulation despite taking into consideration anisotropy in grain boundary energy as well as its mobility. This indicates that grain boundaries produced by severely deformed Zr are stable against explosive coarsening. The evolution characteristics of the microstructure in the present ECA pressed and recrystallized Zr differed from those of cold rolled Ti in that the grain boundary misorientation distribution and texture were rather stable during grain growth. Jointly Appointed by the Center for Advanced Aerospace Materials This article is based on a presentation made in the 2002 Korea-US symposium on the “Phase Transformations of Nano-Materials,” organized as a special program of the 2002 Annual Meeting of the Korean Institute of Metals and Materials, held at Yonsei University, Seoul, Korea on October 25–26, 2002.     

热压变形对灰口铸铁石墨形态的影响

研究了灰口铸铁(HTl50)在900℃大压下量塑性变形后石墨的分布形态，结果表明：随着压下量的增加，石墨片逐渐趋于平行分布；变形过程中发生了碳的回溶，同时伴随着石墨片的断裂；石墨片体积分数及片间距随压下量的增加而逐渐减少。     

Effects of annealing at high pressure on structure and mechanical properties of Al87Ni7Gd6 metallic glass

The effects of annealing and annealing with a superimposed pressure of 940 MPa on the primary crystallization behaviour of α-Al and the resulting micro-hardness have been studied for as-quenched Al₈₇Ni₇Gd₆ metallic glass. Isothermal annealing experiments were conducted for 30 min at 188 °C, 191 °C, and 205 °C in silicone oil maintained either at atmospheric pressure (i.e. 0.1 MPa) or at 940 MPa. XRD analyses detected the evolution of structure with annealing at 0.1 MPa, while specimens annealed with 940 MPa pressure exhibited sharper diffraction peaks than those annealed at 0.1 MPa. DSC measurements were conducted on the as-received amorphous ribbons as well as ribbons annealed at different temperatures at either 0.1. MPa or with 940 MPa superimposed pressure. Specimens annealed with 940 MPa pressure exhibited higher onset temperatures (i.e. T_x1) and temperatures for the first exothermic peak (i.e. T_p1) for primary crystallization. TEM measurements revealed an increase in the volume fraction of α-Al with increases in annealing temperature, while micro-hardness measurements revealed an increase in hardness with increasing amounts of α-Al. Specimens annealed with 940 MPa pressure exhibited further increases in both the volume fraction of α-Al and resulting micro-hardness.