气相色谱在线分析变压吸附法制纯氢中的总碳

利用带镍加氢转化炉的气相色谱仪 ,在线分析变压吸附法制纯氢中的总碳。该法用变压吸附法制的纯氢作燃气 ,在检测器前端将氢气中的CO和CO2 转化为CH4,然后用氢火焰离子化检测器检测 ,直接以检测器的信号 (mV)进行定量。当氢气中总碳体积分数在 1 9～ 5 0 0 μl/L时 ,FID信号值与总碳体积分数有良好的线性关系。方法回收率为 99 90 %～ 10 1 9%,相对标准偏差 <1%。     

催化裂化烟气转硫脱氮和助燃三功能催化剂FP-DSN的工业应用

烟气转硫、脱氮和助燃三功能新型催化剂FP DSN在中国石油天然气股份有限公司锦西石化分公司 1.4Mt/a重油催化裂化装置的工业应用表明 ,此种以La ,Ce ,Sr和Co等元素的氧化物或复合物为活性组分的催化剂 ,在其用量为催化裂化催化剂总藏量的 1%～ 2 %的情况下 ,有较强的脱除烟气中SOx 和NOx 的能力 ,大大减轻了烟气对反应器壁的腐蚀 ,减少了污染气体的排放 ,同时有CO助燃效果 ,装置可不使用其他专门的助燃剂。应用试验时 ,再生器烟气中SOx 的平均脱除率达 72 .85 %,NOx 的平均脱除率达 85 .90 %。该催化剂的使用对催化裂化产品的分布和质量无明显影响。该剂的应用为装置带来了可观的经济效益。     

非化学计量LaNi5型储氢合金的性能

采用富La混合稀土与Ni、Co、Mg等元素组合，获得了一种非化学计量LaNi5型储氢合金、用金相、XRD和SEM-EDX等方法分析了该合金的组织结构，研究了合金的气相储氢特性以及电化学性能，结果表明：在1.6MPa氢压和温度29℃下，该合金的储氢量达到1.58%（质量分数），该合金的放电容量为380mAh/g。经300次循环后容量保持率为55%，该合金的基体是CaCu5型结构的LaNi5相，但有第二相（LaMg)Ni3析出，这种第二相的形成是导致该合金大容量的关键。     

Lyapunov‐stable discrete‐time model reference adaptive control

Discrete‐time model reference adaptive control (MRAC) is considered with both least squares and projection algorithm parameter identification. For both cases complete Lyapunov proofs are given for stability and convergence. The results extend the approach of Johansson (Int. J. Control 1989; 50 (3):859–869) to include Lyapunov stability for MRAC when the normalized projection algorithm is used for parameter identification. Copyright © 2005 John Wiley & Sons, Ltd.     

Quantitative evaluation of generator power control effect of FACTS controllers for power system stabilization

The advancement of power electronics technologies has significantly developed the power system stabilizing controllers. Quantitative as well as qualitative evaluation of their effectiveness in power systems is a matter of great importance for the feasibility investigation of these apparatus. In this paper, the possible control region of FACTS controllers with series and/or shunt configuration in a single machine to infinite bus system is formulated in the powerangle curve with a set of algebraic equations. The effectiveness of TCPST (Thyristor‐Controlled Phase Shifting Transformer), SSSC (Static Synchronous Series Compensator), and TCSC (Thyristor‐Controlled Series Compensator) for the improvement of the transient stability is evaluated quantitatively as a numerical example. The correctness of the proposed method has been confirmed by analysis based on the electromagnetic transients simulation with a detailed system model. © 2001 Scripta Technica, Electr Eng Jpn, 138(3): 43–51, 2002     

Ionoluminescence decay measured with single ions

A new ion beam analysis-based, single ion technique called the time to first photon has been developed to measure the decay of the luminescence signal of phosphors. Such measurements are currently needed to study luminescence decay mechanisms following high-density excitations and to identify strongly luminescent phosphor coatings with short lifetimes for ion photon emission microscopy (IPEM). The samples for this technique consist of thin phosphor layers placed or coated on the surface of PIN diodes. Single ions from an accelerator strike this sample and simultaneously create ion beam induced luminescence (IBIL) from the phosphor that is measured by a single-photon-detector, and an ion beam induced charge collection (IBICC) signal in the PIN diode. In this case, the IBICC signal provides the start pulse and the IBIL signal the stop pulse to a time to amplitude converter. It is straightforward to show that this approach also measures a signal proportional to activity versus time with an accuracy of 5% as long as the number of detected photons per ion is less than 0.1, which usually requires the use of absorbers for the IBIL detector or electronic discrimination for the IBIL signals. Details of the new analysis are given together with examples of luminescence decay measurements of several ceramic phosphors being considered to coat IPEM samples. IPEM is currently being developed at Sandia National Laboratory (SNL), the University of North Texas in Denton, and the Universities and INFN of Padova and Torino.     

Metallurgical failure analysis of cold cracking in a structural steel weldment: Revisiting a classic failure mechanism

Cold cracking of structural steel weldments is a well-characterized, well-documented, and well-understood failure mechanism. Extensive effort has been put forth to recognize the welding and materials selection parameters that are conducive to cold cracking; however, these engineering efforts have not fully eliminated the occurrence of such failures. This article describes cold cracking failure specifically related to the construction industry. This particular failure was successfully identified prior to final erection of the structural member, and the weld was successfully reworked. These actions potentially prevented a serious catastrophic event that could have occurred have occurred either later in the construction process or possibly during the use of the building. Individual welding parameters, such as electrode/wire selection, joint design, and pre/postheating, played a role in the failure, and a number of human factors relating to the actual fabrication practices also contributed to the failure process.     

改进催化裂解装置再生立管气固输送状态

荆门分公司催化裂解装置由于使用高堆密度催化剂，再生立管出现了气固输送故障，对反应温度和产品收率影响较大。采取改进措施后取得了显著效果，液化气收率可提高约4个百分点，丙烯收率可提高1－3个百分点。     

Measurements of turbulent mass transport of a circular wall jet

The results of a laboratory investigation on the turbulence characteristics of a circular three-dimensional turbulent wall jet are presented. Measurements were taken up to 50 nozzle diameters using combined particle image velocimetry and planar laser induced fluorescence. The results showed that the induced turbulence was still evolving in the present range and had not achieved similarity. While the turbulent intensity for both velocity and concentration increased downstream, the turbulent mass transport showed a decline over distance for both the streamwise and spanwise directions, implying weakening dispersion from the jet core.