卟啉类光电功能材料的研究进展

卟啉及其衍生物是一类具有优良的光电性能的有机半导体材料．引起人们广泛的关注。本文对卟啉类光电材料在模拟生物光合作用中心的光致电荷转移和能量转移，有机太阳能电池．分子光电器件。有机电致发光和光存储等领域的研究进展做一简要介绍。     

胶性材料在混凝土坝裂缝处理中的应用

介绍了观音阁坝被埋水下6年越冬停浇面水平裂缝采用“粘贴T1密封胶及表面粘三元乙丙后锚固”的处理方案。结果表明,利用胶性材料处理运行中的重力坝迎水面裂缝,技术可靠,方法简单,经济合理。     

Effect of Stoichiometry on Properties of Rare-Earth-Based Hydrogen Storage Alloy for Nickel-Metal Hydride Secondary Battery

Effect of stoichiometry on microstructures, electrochemical properties and PCT characteristics of the alloys MI(Ni0.71Co0.15-Al0.06Mn0.08)x (MI=Lanthanum-rich Michmetal, x=4.6~5.2) have been investigated. The lattice constants a, c, and cellvolumes of non-stoichiometric alloys are bigger than those of the stoichiometric alloy. With the increasing stoichiometry x,the value of a decreases, and the value of c and cell volume increases except for those of the stoichiometric alloy; the plateaupressure of PCT curve, discharge capacity and cycling stability all increase. The alloy with x=5.2 shows the highest dischargecapacity and the best cycling stability among the studied alloys.     

偶氮聚合物光存储研究进展

着重阐明了偶氮聚合物光存储纪录的原理,分析了其双折射特性的微观机制,介绍了该课题近年来实验和理论上的最新进展,对这一充满希望和挑战的多学科交叉研究专题作了展望。     

硫化氢吸收液的电化学分解条件研究

理想的脱硫工艺应满足体积小、费用低、净化度高、无二次污染等要求。在碱性溶液吸收微量硫化氢时同步进行电解，可有效减小设备体积，并将硫化氢转变为氢气和硫磺，不产生恶性气味。为此，实验研究了温度、浓度、电流密度、pH值等因素对电解阳极过程的影响，确定了适宜的电解条件，并在该条件下进行了吸收实验。结果表明，在最佳电解条件下，硫化钠溶液能充分吸收天然气中经变压吸附提浓的硫化氢（800 mg/m³），吸收率大于99.9％。     

橡胶促进剂DM的合成工艺

M氧化生成DM是自由基反应机理，结合微反应器机理，采用分子氧化的反应方式，选用绿色溶剂异丙醇、环境友好型氧化剂H202，一步法制取高品质DM。对反应时间、反应温度、氧化剂用量等因素进行考察，确定最佳工艺条件为：反应时间90min，反应温度55℃，氧化剂不过量，碱过量5％，M—Na溶液M含量30％，加料时N60 min，溶剂用量为M—Na溶液质量的1．5倍，所得产品质量合格，熔点可达180℃。     

高密度互连印制板

本文阐述了RCC材料与化学蚀刻法制作高密度互连印制板的工序和详细方法,意在探寻最为经济、简单而又行 之有效的工艺。     

新型微光探测器激光防护材料的研究

系统分析了微光夜视器的结构及其原理，并结合当前器件存在的激光致盲威胁，提出了增强系统安全的新措施。同时，系统地介绍了防激光滤光材料一些重要的性能参数以及滤光材料的组成、制备加工工艺。研究结果表明，新型的防激光材料能够有效地防护800nm，900nm以及10613nm等三个波长的激光，并且可见光透过率大于85％。     

气调库及气调库设备

分析果蔬贮藏保鲜期的生理变化，介绍气调保鲜库设计施工验收中的技术要求，保鲜工艺和主要设备。     

Non-equilibrium particle motion in the vicinity of a single blade

The motion of sand particles close to a single moving blade was investigated using Positron Emission Particle Tracking (PEPT) during the period in which the free bed surface profile was evolving to an equilibrium shape. The area affected by the blade was divided into active and inactive regions and these were analysed separately. The characteristic heart-shape of the active region in the plan view was determined. An approximately 10-particle-diameter wide velocity transition zone is found between the two regions. While the tracer particle is in the inactive region moving away from the blade, the time dependence of the axial displacement is well described by a logarithmic relationship. The probability of particle movement towards the centre of the blade was quantified using a “central tendency” index. The calculated central tendency shows maxima at each side of the blade. The separation of the two maxima, which indicates the width of the active region, increases with fill level but is independent of rotational speed.