热释电红外摄像机斩波调制电路的设计

本文提出了热释电红外摄像机斩波调制的电路模型，并对此电路模型进行了具体的电路设计和分析。     

有梭织机光电探纬系统的改进

依据红外反射式光电探纬的组成和工作原理，对有梭织机光电探纬系统进行了改进。将反光装置（膜）固定在梭芯上，减少了反光装置的数量，无需改动梭子和纬管，系统探纬准确，减少了换梭时纡脚回丝。     

Hybrid gas-to-particle conversion and chemical vapor deposition for the production of porous alumina films

Porous alumina films can be found in a wide variety of materials, including filters, thermal insulation components, dielectrics, biomedical and catalyst supports, coatings and adsorbents. Production methods for these films are as equally diverse as their applications. In this work, a hybrid process based upon chemical vapor deposition and gas-to-particle conversion is presented as an alternative technique for producing porous alumina films, with the main advantages of solvent-free, low substrate-temperature operation. In this process, nanoparticles were produced in the vapor phase by reaction of aluminum acetylacetonate in the presence of oxygen. Downstream of this reaction zone, these nanoparticles were collected via thermophoresis onto a cooled substrate, forming a porous film. Some deposited films were subjected to post-processing in the form of annealing in air. Fourier-transform infrared spectra and X-ray energy-dispersive spectroscopy analysis confirmed the production of alumina at processing temperatures above 973 K. X-Ray diffraction revealed that the films were amorphous. Film thickness, ranging from 30 to 250 μm, and the average deposition rate were determined from scanning electron microscopy results. From transmission electron microscopy, the average primary particle size was determined to be approximately 18 nm and the formation of nanoparticle aggregates was evident. Annealing of the films at temperatures ranging from 523 to 1173 K in the presence of air did not have an effect on particle size. The specific surface area of the powder composing the films ranged from 10 to 185 m² g⁻¹, as determined from nitrogen gas adsorption by the Brunauer–Emmett–Teller method.     

源气体流量比对F-DLC薄膜结构的影响

以高纯石墨作靶，CHF3/Ar作源气体采用反应磁控溅射法制备出了氟化类金刚石（F-DLC）薄膜。拉曼光谱表明，CHF3相对流量的增加会引起薄膜的D峰与G峰强度之比I（D）/I（G）减小，晶粒增大，芳香环结构出例下降。红外吸收光谱分析证实了这些推论，指出这是由于薄膜中氟含量上升的结果。     

燃气红外线辐射器的节能与环保特性分析

论述了燃气红外线辐射器的基本原理 ,对其节能与环保特性的分析表明 :与大气式燃烧器相比 ,红外线辐射器的燃料节约率为 15 %～ 45 % ,CO2 排放量减少率为 15 %～ 48% ,CO排放量减少率为 96.2 %～ 97.7% ,NOx 减少率为 94.9%～ 96.9% ,具有显著的节能与环保效果     

Thermal Evaluation of Scorched Graphite-Epoxy Panels by Infrared Scanning

A simple measurement system is described for evaluating damage to graphite-epoxy panels, such as those used in high-performance aircraft. The system uses a heating laser and infrared imaging system to measure thermal performance. Thermal conductivity or diffusivity is a sensitive indicator of damage in materials, allowing this thermal measurement to show various degrees of damage in graphite-epoxy composites. Our measurements track well with heat-flux damage to graphite epoxy panels. This measurement system, including analysis software, could easily be used in the field, such as on the deck of an aircraft carrier or at remote air strips.     

量子阱红外探测器能带结构的计算

利用电子波在阱与垒的界面上的反射及干涉效应，计算了量子阱红外探测器(QWIP)的能带结构，并对其适用性进行了分析和讨论。通过与K-P模型比较发现，本方法对计算较宽势阱(阱宽大于4nm)的量子阱结构的电子态适合。在垒宽和阱宽不变条件下，用两种方法计算得到的AlGaAs／GaAs量子阱材料中Al组分x与吸收峰值波长λp的关系曲线基本相同。结果说明，在较宽的范围内，本方法对QWIP能带结构的计算是适用且简便的。     

低发射率材料红外法向发射率谱测量方法的研究

采用热管技术研制了材料发射率谱的专用测量附件;利用双温测量技术,在P-E983型红外分光光度计及3600型数据站上进行了较低温度下低发射率材料红外法向发射率谱测量方法的研究.实测了几种材料的发射率谱;讨论了影响测量误差的诸因素.     

Linked influence of pH and cations on fatty-acid monolayer integrity related to high-quality Langmuir-Blodgett films

This study shows the connection between the morphological structure of transferred films and the chemical composition of the monolayer before transfer. The stability of a behenic acid monolayer depends on the linked influence of the type of cation and of the pH value in the aqueous subphase. The stability of the monolayer is assessed by the expansion of the solid-packed state and by the relaxation time. Its integrity is characterized by the number of crystal defects which appear in transferred Langmuir-Blodgett (LB) films as seen through Nomarski microscope observations. Both stability and integrity are greatly improved when Cd²⁺ or Mn²⁺are added to the subphase at pH 5.75 and 6 respectively. In these conditions, the transfer is very efficient and the LB films thus obtained are of very high quality. The pH values of the subphase at which the molecules of behenic acid are transformed into bivalent salts differ significantly according to the nature of the cation involved. Comparing infrared spectra of the LB films, it appeared that the relative amount of acid/salt found in the monolayer was practically the same with a subphase containing either Cd²⁺ at pH 5.75 or Mn²⁺ at pH 6. This suggests that the ratio of acidic and salt forms would be a key parameter for obtaining high-quality LB films.