复合材料一体化钻井泵缸套产业化技术研究

介绍了复合材料一体化钻井泵缸套在产业化过程中的若干关键技术。通过对缸套内套材料成分和组织的优化研究,双液分时离心浇注工艺优化研究以及双液离心浇注工装开发,实现了新工艺缸套的产业化。与现行的热镶装双金属缸套工艺相比,采用新技术生产的缸套平均使用寿命超过750h,生产成本下降了20%。     

浇筑式沥青混凝土心墙型式改进的建议

本文根据浇筑式沥青混凝土主、副心墙材料的性能，分折了沥青混凝土心墙施工或运行中破坏的原因，建议用编织一无纺复合布取代预制块，以避免主、副心墙材料变形性能相差悬残对心墙运行的不利影响，从而发挥浇筑式沥青混凝土心墙的优越性。     

Cable Modem的原理与反向噪声的控制

介绍Cable Modem的基本概念、传输方式、标准规范，并对影响Cable Modem工作稳定性的反向噪声问题进行技术分析，并提出预防控制措施。     

Profiling Voids Embedded in a Slab by a Non-Linear Model

In this paper, by applying a non linear model for the electromagnetic inverse scattering, a technique for the dielectric profiling of a planarly layered medium is investigated and applied to void localization and diagnostics inside a homogeneous lossless slab (one-dimensional geometry). Data are collected under plane wave multifrequency normal incidence. Suitable finite dimensional representations for the unknown functions are introduced and their influence on the model is discussed. The resulting functional equation is solved by the method of weighted residuals and the solution algorithm amounts to minimizing a non quadratic function, where particular attention is devoted to reduce the occurrence of local minima. Finally, the inversion algorithm is validated by applications to both simulated and experimental data.     

真空铸造高强度C/Mg复合材料

本文介绍用真空铸造法制造抗拉强度超过1000MPa的高强度C/Mg复合材料。将T300纤维经C-Si-O梯度涂层处理后单向排布于型腔内,在真空下注入ZM-5合金液,凝固后即得C/Mg复合材料零件或试样。试样的抗拉强度在纤维体积分数为0.35时达1050MPa。本文讨论C-Si-O梯度涂层对获得高强度复合材料的作用。     

放置过滤器浇注系统的设计

综述了常用的网型、芯型、泡沫陶瓷过滤器的研究和应用情况。指出应根据过滤器类型，确定其在浇注系统中的安放位置并相应改变该处的结构和截面积，以便在使用过滤器净化金属的同时，保证充型速度不变。     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

8Li次级束的产生

在北京串列加速器次级束流线上通过2 H(7Li,8Li) 1H逆运动学反应产生了用于核天体物理研究的8Li次级束。准直后的次级束纯度达到 80 %以上 ,对于 44MeV的7Li强度约为 3 0s- 1·pnA- 1,可以用来进行逆几何转移反应的实验测量。     

连铸机油缸成套密封件国产化

本文论述了冶金行业中连铸机油缸密封件国产化的一些技术参数，同时也介绍了洪格尔型组合密封及夹布V型圈组合密封的使用特点。