Influence of isothermal aging onσprecipitation in super duplex stainless steel

The time-temperature-transformation (TTT) curve of the 00Cr25Ni7Mo4N duplex stainless steel was obtained with a Formastot-digital thermal dilatometer,and the influence of isothermal aging on σ precipitation was studied by metallographic observation,X-ray diffraction (XRD),and transmission electron microscopy (TEM).The results show that the decomposition of ferrite phase is accompanied by the formation of σ phase at 750-1000℃,especially in the range of 800-900℃.The longer the aging time,the higher the amount of σ precipitation.The area fraction of various phases remains at a certain value upon the completion of ferrite deformation.The temperature of 850℃ is the most sensitive transaction temperature,the incubation time for the formation of o precipitation is less than 1 min,and aging for 20 min leads to the complete transformation of ferrite.The o phase is formed preferentially at the α/α/γ junction,and then grows along the α/α boundary in the matrix.     

Electrical conductivity changes of bulk tin and Sn-3.0Ag-0.5Cu in bulk and in joints during isothermal aging

The changes of electrical conductivity(resistance) between Sn-3.0Ag-0.5Cu solder joints and printed circuit board(PCB) assembly during aging at 125℃were investigated by the four-point probe technique.The microstructural characterizations of interfacial layers between the solder matrix and the substrate were examined by optical microscopy and scanning electronic microscopy.Different types of specimens were designed to consider several factors.The experimental results indicate that electrical conductivitie...     

Effect of cooling rate on the phase transformation and stability of the mushy zone during the solidification of Waspaloy

Scanning electron microscopy(SEM) and energy dispersive X-ray analysis(EDAX) were used to study the microstructure,microsegregation, and fluid flow tendency of the superalloy Waspaloy in the mushy zone,which had been solidified at different cooling rates. The investigation was accompanied with the calculation of Rayleigh numbers.It is found that Ti is the main segregating element and the content of Ti is the highest in the final liquid at the cooling rates of 3-6℃/min.The eta phase(η) precipitate present...     

Cycling hardening and serration yielding of Fe-Ni-Cr alloy at high temperature under out-phase TMF

Behaviour of hardening and serration yield of a Fe-Ni-Cr alloy under isothermal cycling (ISC) and out-phase TMF was studied on the basis of varied hysteresis loops. Cycling hardening and serrated yielding for ISC depend on the temperature and the total strain range, stronger hardening with serrated yielding at higher strain range under ISC at 600 °C, but no hardening and serrated yielding occurred under ISC at 800 °C. Stronger hardening with stress serration occurred at the thermal path going to the lowest temperature, no stress serration occurred at the highest temperature under the out-phase. The hardening also depends on the total strain range, higher total strain range with lower cycling temperature resulted in a stronger hardening and remarkable serration yielding behavior. Weaker hardening without serrated yielding occurred at near 800 °C may due to an obvious cycling stress drop under out-phase TMF. Change in the shape of the hysteresis loops also expresses the degree of the damage of the tested alloy under out-phase and ISC.     

Formation of bulk ferromagnetic nanostructured Fe_(40)Ni_(40)P_(14)B_6 alloys by metastable liquid spinodal decomposition

Nanostructured Fe40Ni40P14B6 alloy ingots of 3―5 mm in diameter could be synthesized by a metastable liquid state spinodal decomposition method. For undercooling T> 260 K, the microstructure of the undercooled specimen had exhibited liquid state spinodal decomposition in the undercooled liquid state. The microstructure could be described as two intertwining networks with small grains dispersed in them. For undercooling T>290 K, the overall microstructure of the specimen changed into a granular morphology. T...     

定向凝固纯铜组织性能研究

采用高真空多功能定向凝固及悬浮熔炼设备,以不同凝固速度制备纯铜试样,并对定向凝固纯铜试样的显微组织和机械性能进行了分析研究.通过实验获得了定向凝固纯铜的组织性能.当凝固速度小于500μm/min时,定向凝固的纯铜试样横、纵截面的晶粒形貌都是等轴晶,晶粒内存在孪晶,凝固速度较小时,其孪晶组织数量较多.当凝固速度大于500μm/min时,定向凝固的纯铜试样横截面的晶粒形貌是等轴晶,而纵截面的晶粒形貌是柱状晶,晶粒内基本不存在孪晶组织.定向凝固纯铜的室温机械性能是:当凝固速度在50μm/min的条件下,试样的抗拉强度约153 MPa,较普通铸造纯铜试样的低,而屈服强度约91.8 MPa,延伸率约80.12%,都优于普通铸造纯铜试样.透射电镜分析表明,纯铜定向凝固过程中形成的孪晶B=[110].     

混配柴油凝点及溶解度参数的分子模拟研究

石化柴油中添加少量生物柴油调配混配柴油是当前研究的一个热点.分别用单组分、3组分和5组分正构烷烃构建石化柴油模拟系统,以亚油酸甲酯（ML）构建单组份生物柴油模拟系统.按2％、4％、6％、8％和10％物质的量比添加ML于石化柴油模拟系统中构建不同比例的混配柴油系统.利用分子动力学方法对各种系统的凝点区间及溶解度参数进行了模拟计算.利用热容等4个性质联合判断出各系统的模拟凝点区间,发现,随着ML的添加,系统的凝点总体呈下降趋势,说明生物柴油确具有明显的降凝效果,添加生物柴油可以使柴油的低温流动性增加.相比较而言,采用3组分正构烷烃构建石化模拟系统更为合适.通过对293 K时3组分石化柴油系统添加不同比例的ML构成的混配柴油系统的溶解度参数进行分析,得出了当添加比例为4％时两种油品的相容性最佳的结论.     

喷射成形1.8C-1.6Al超高碳钢快速凝固组织研究

铸造1．8C-1．6Al超高碳钢(UHCS)由于冷速较低，晶粒粗大，珠光体片间距也较大，品界形成了粗大的碳化物网络，同时合金元素产生偏析，品内生成了大块的合金渗碳体，使得它在室温下为脆性，机加工性能极差。喷射成形1．8C—1．6Al超高碳钢则利用喷射成形工艺冷却速度大的特点细化了晶粒，减小了珠光体的片间距，提高了硬度与强度，同时降低了元素偏析程度。同时发现：在铸态1．8C-1．6Al超高碳钢中和在喷射成形1．8C-1．6Al超高碳钢中Al在晶内的分布情况正好相反，由反偏析转变为正偏析。     

快速凝固TiAl基合金微晶的显微组织

用气体雾化方法制备了Ti-34Al-2Mn合金的微晶粉末,粉末典型粒度为27μm。X射线衍射结果表明,快冷态的粉末主要由α_2相和少量γ相组成。金相组织显示出等轴块状晶粒和树枝状结晶两种形态。经900℃,2h真空退火后,大部分α_2相转变成γ相,使原来的组织更加细化。