轧机主传动万向联轴器辊端接头结构探讨

分析了衬板槽平面与叉头十字轴孔轴线的相对位置对辊端接头应力的影响 ,研究了轧辊扁头与衬板之间间隙所产生的冲击和应力集中 ,讨论了辊端接头中部过渡段结构对应力分布和制造质量的影响。提出辊端接头结构设计的优化方案     

Modeling and simulation of a fully air swept ball mill in a raw material grinding circuit

A raw material grinding circuit was modeled using plant data. Samples were collected from around the circuit and, following a crash stop, from inside the mill. The size distributions of the samples were determined down to a few microns. Using the data from inside the mill a modeling approach, based on perfect mixing, was developed. The modelling approach implicitly assumes that the mixture of feed materials broken is homogenous from the breakage point of view. The air classification around the circuit was modeled using the efficiency curve approach. In order to measure the success of the method the circuit performance was predicted by simulation studies while it was operating at different conditions. The results were then compared with the measured data. It is concluded that modeling gives a useful quantitative indication of what may occur in fully air swept mills.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

Time Characterization of High Density Gas Jet from a Pulsed Supersonic Nozzle via Laser Produced Plasma

A high-density gas jet supersonic nozzle is reported in this paper. The jitter and actuation time of the nozzle is determined by the pin discharge and laser spark radiation respectively. The jitter time of the nozzle is within 10μs with the backing pressure as high as 25 bar. With a nanosecond laser pulse focused on the gas jet about 1 mm below the nozzle, the actuation time is calculated to be about 15 ms by detecting the laser produced spark radiation, which reveals the existence of the gas jet and the relative gas density evolving with time. Consequently the gas density is estimated to be well above 10^19 cm^-3, compared with theoretical simulations from the nozzle parameters.     

Preparation of clean coal by flotation following ultra fine liberation

This paper reports the results of current fundamental research at the Department of Process Engineering, University of Miskolc on the processing of clean coal from Mecsek bituminous coal, Southern Hungary. The theoretical possibility of the separation of different petrographic components was proven experimentally and their liberation degree was determined based on the petrographic composition, flotation kinetic study of isolated components (groups of components), scanning electron microscopy and microprobe analyses. The mill with stirred ball media was chosen for the ultra-fine liberation of the coal components. It was revealed that along with the liberation of coal components, their surface oxidation and spontaneous agglomeration, entrapping the mineral impurities take place in ultra-fine grinding. This paper discusses the interfacial phenomena occurring in the ultra-fine grinding process and their influence on the flotation. The concept for the advanced preparation of clean coal was developed, tested and proved. The main steps of this concept are the ultra-fine liberation in the stirred-media mill, the de-agglomeration of flocs spontaneously formed during the ultra-fine grinding and the induced (hydrophobic) flocculation with the following two-step flotation in a flotation column.     

制备单根大重量喷涂钼丝的生产研究

全面系统地介绍了“大坯料轧制开坯-大加工率变形-长线拉伸”制造喷涂钼丝的工艺。重点阐述了Y370、Y250型三辊连轧机实现一火轧制开坯和长线拉伸增加在线碱洗工序对提高喷涂钼丝内部组织结构和外部表面质量的影响。分析了工艺中出现的问题，提出了相应的解决办法。     

JETS,PLUMES AND BUOYANT JETS IN STATIC ENVIRONMENT

Turbulence represents an essential aspect in atmospheric and oceanic circulations.In particu-lar,it is a preponderant factor in the dispersion of pollutants of artificial or natural origin.Thevertical turbulent jets,plumes and buoyant jets discharging into static environment is one of themost important and basic flow patterns related with the environment pollution.These flows havenumerous important applications,for example,thrust augmentors,waste disposal plumes fromstacks and combustion systems,and significant problems of turbulent diffusion.     

复印粉的粉碎分级技术

本文介绍了利用国产气流粉碎机和余气萃取分级制备复印粉的实用技术，并展示了粉碎分级系统和复印粉的电镜照片。     

连轧管“竹节”问题的研究

本文就各工艺参数对“竹节”的影响进行了较系统的试验。在此基础上，对连轧管“竹节”问题进行了分析，得出了“竹节”形态的基本特征；后“竹节”与轧制压力的关系；影响后“竹节”的主要工艺因素等一系列有意义的结果。对前、后“竹节”形态明显不同的原因进行了初步探讨。提出了“竹节”在线控制模型的初步设想。