任意型一维FIR数字滤波器设计新方法

本文介绍了一种设计任意型（宽带、窄带、低阶、高阶、低通、高通、带通、带阻）一维FIR数字滤波器新方法．给出设计不同类型滤波器的统一方法。各种类型滤波器脉冲响应的设计公式简单、计算方便。该方法消除了Gibbs现象．不仅克服了优化设计中收敛速度、设计精度及初值选取等问题，而且减少设计高阶滤波器的时间。最后，本文给出了各种类型滤波器设计的仿真结果。     

AN EXTENDED MODELING OF TIDE-WAVE MOTION

1 .　ＩＮＴＲＯＤＵＣＴＩＯＮＴｏｓｔｕｄｙｔｈｅｍｏｔｉｏｎｏｆｔｈｅｔｉｄｅ ｗａｖｅｓ,ｔｈｅｓｈａｌｌｏｗｗａｔｅｒｅｑｕａｔｉｏｎｓ ,ｉ.ｅ .ｔｈｅｖｅｒｔｉｃａｌｉｎｔｅｒｇｒａ ｔｉｏｎｏｆｔｈｅｃｏｎｔｉｎｕｉｔｙｅｑｕａｔｉｏｎａｎｄｍｏｍｅｎｔｕｍｅｑｕａ ｔｉｏｎ ,ｉｓｃｏｎｓｉｄｅｒｅｄａｓｔｈｅｇｏｖｅｒｎｉｎｇｅｑｕａｔｉｏｎｓ.Ｂｙａｂｏｖｅｅｑｕａｔｉｏｎｓｔｗｏｅｑｕａｔｉｏｎｓｒｅｌａｔｅｄｔｏｔｈｅｈｏｒｉｚｏｎ ｔａｌｆｌｕｘｏｆｔｈｅｔｉｄｅ ｃｕｒｒｅｎｔｓａ…     

Ti-23Al-14Nb-3V合金氩弧焊接头的显微组织及其力学性能

研究了预热对Ｔｉ－２３Ａｌ－１４Ｎｂ－３Ｖ合金焊接性，特别是对消除氩弧焊冷裂纹的作用以及对接头显微组织和力学性能的影响。结果表明，焊前预热可有效降低该合金的冷裂倾向。经预热处理后，焊缝区的结晶层状线消失，热影响区的硬度峰得到缓和，整个焊缝的显微硬度分布趋于均匀，但焊缝区的枝晶发生粗化，热影响区有所扩大。焊件接头的拉伸试验表明，预热可使焊缝区的接头强度系数增加，但无论预热与否，接头强度均低于母材强度，且不显示宏观塑性。     

节能润滑油在KTK-12.5/35氧压机上的使用

对氧压机试用节能润滑油前后的相关参数进行比较,通过计算验证该设备使用此油后的节电率,取得了预期的经济效益。     

Application of the dynamical flexural resonance technique to industrial materials characterisation

The determination of the Young’s modulus and damping coefficient Q⁻¹ by means of non-destructive vibrating techniques has been applied to bulk and coated industrial materials. Extensions of a previous analytic model of composite beam allow to determine accurately the macroscopic modulus of each component of multilayered structural materials as coated superalloys or nitride-hardened steels. Furthermore, the study of glasses and polymers has been investigated. An attempt of normalisation of the modulus versus temperature curves allows to establish master curves depending on the specific structure, from metallic glasses to polymeric glasses. Finally a comparison of dynamical modulus and Q⁻¹ values measured between resonant (>1 kHz) and subresonant techniques (10⁻³ to 10 Hz) in relation to the loading frequencies applied in real conditions has been under folder. For metallic materials such as forged or rolled titanium alloys, the brittle-to-fragile transition occurs abruptly or smoothly with a shift of 300 K following the range of excitation frequencies.     

Friction Stir Welding of Ceramic Particle Reinforced Aluminium Based Metal Matrix Composites

The mechanical and microstructural properties of 6061+20% Al₂O_3p and 7005+10% Al₂O_3p aluminium based metal matrix composites joined by friction stir welding were analyzed in the present study. The two materials were welded into the form of sheets of 7 mm thickness after T6 treatment and were tested in tension at room temperature. The microstructure of the joints was observed by optical microscopy and the fracture surfaces were analyzed by employing a scanning electron microscope equipped with field emission gun in order to study the micromechanisms involved during the deformation.     

Low Temperature Elastic Constants of Polycrystalline MgB2

We have used a resonant ultrasound spectroscopy technique to measure the bulk and shear modulus of fully dense, polycrystalline MgB₂ between 4 and 300 K. Both moduli show good agreement with published first principle calculations. The internal friction shows a broad maximum around 40 K.     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

适用于稠油开采的游梁式抽油机设计分析

在稠油开采中,抽油杆在液体中运动时,所受到的摩擦阻尼力很大,有时高达几十千牛。上冲程时,该力有加大悬点载荷的作用;下冲程时,该力使抽油杆下行困难,甚至悬点载荷为零。为了开采稠油,必须根据其特点设计适应的游梁式抽油机。文章分析了稠油用抽油机的受力特点,提出了该类抽油机的设计要求。