Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism     

Low-temperature catalytic combustion of methane over MnO x –CeO2 mixed oxide catalysts: Effect of preparation method

The effect of preparation method on MnO _x –CeO₂ mixed oxide catalysts for methane combustion at low temperature was investigated by means of BET, XRD, XPS, H₂-TPR techniques and methane oxidation reaction. The catalysts were prepared by the conventional coprecipitation, plasma and modified coprecipitation methods, respectively. It was found that the catalyst prepared by modified coprecipitation was the most active, over which methane conversion reached 90% at a temperature as low as 390 °C. The XRD results showed the preparation methods had no effect on the solid solution structure of MnO _x –CeO₂ catalysts. More Mn⁴⁺ and richer lattice oxygen were found on the surface of the modified coprecipitation prepared catalyst with the help of XPS analysis, and its reduction and BET surface area were remarkably promoted. These factors could be responsible for its higher activity for methane combustion at low temperature.     

轻烃净化分离工艺安全高效运行措施探析

宝浪联合站轻烃工艺装置是宝浪油田甲级防火、一级防爆的关键装置。其主要功能是净化分离并回收原油中易挥发的轻质成分,生产以C3和C4为主要成分的液化石油气,分离出以C1和C2为主要成分的干气供宝浪油田油区发电和周边居民生活用气。在系统运行过程中,发现装置低温分离工艺中有不利于安全的因素,而消除这些因素对消除安全隐患、提高液化气产量和减少有效成分损失等起决定性的作用。     

分数布朗运动下的可分离债券定价

假定股票价格服从分数布朗运动,且无风险利率为时间的确定性函数,股票价格的波动率为常数。利用分数布朗运动随机分析理论与方法,建立股票价格服从分数布朗运动的金融市场数学模型,并得到了可分离债券的定价公式。     

兆瓦级风电球铁件低温冲击韧性的影响因素

为了获得具有良好低温冲击性能的兆瓦级风电球铁铸件,对实际生产中的附铸试件-20℃ V型缺口冲击性能进行了测试,并对其成分、基体组织、石墨球大小及分布情况进行分析,研究了兆瓦级风力发电机组球铁件低温冲击韧性影响因素.结果表明：在低P、S的前提下,通过合理的熔炼工艺控制,终Si量在2.3%时可以使单位面积的石墨球数量增加,石墨球细小,低温冲击值最佳;Mn在0.2%~0.3%之间变化时对低温冲击韧性影响并不明显;基体组织中珠光体在5%以下时,低温冲击值无明显变化,珠光体大于12.5%时,低温冲击值急剧下降.     

专用粉末涂料和涂装发展的新展望

新型专用粉末涂料以其涂膜超薄型化、低温固化和高耐候性等优势,并以预裁割坯料新工艺代替预涂装卷材工艺的新特点,将成为粉末涂料新的增长点。还提出了若干建议和意见。     

桥面铺面防水粘结层胶结材料洒布量的确定方法

为确定桥面铺面防水粘结层胶结材料洒布量,采用橡胶沥青和两种典型的沥青混合料,通过设计直向剪切试验和斜向剪切试验研究桥面防水粘结层的力学性能,分析不同因素对于防水粘结层剪切性能的影响．试验结果表明,加载速率的提高,粘结层最大剪切应力有呈线性增大的趋势;采用不同温度的对比试验,同样发现随温度的升高,其抗剪切能力显著衰减．可以通过剪切试验的剪应力和变形能两个指标评价其剪切性能．     

铜参与的三氟甲硫化反应研究进展

由于三氟甲硫基强的吸电子作用、亲脂性和疏水性,三氟甲硫醚类化合物在生物、医药和农药等领域得到了广泛应用,其合成方法也逐渐成为有机化学领域的研究热点之一,其中铜试剂参与的三氟甲硫化反应发展迅速.按照参与三氟甲硫化反应底物的不同,主要综述了各种铜试剂参与的卤代烃、芳基硼酸、C-H键活化等方面的三氟甲硫化反应的研究进展.     

Atomic layer deposition of GDC cathodic functional thin films for oxide ion incorporation enhancement

In this paper, we report successful fabrication of a gadolinia-doped ceria (GDC) thin film using atomic layer deposition (ALD) for improving the performance of solid oxide fuel cells (SOFCs). By varying the deposition conditions and adjusting the configuration of the ALD supercycle, the doping ratio of ALD GDC was controlled. The morphology, crystallinity, and chemical composition of ALD GDC thin films were analyzed. ALD GDC showed different surface chemistry, including oxidation states, at different doping ratios. The application of ALD GDC in a SOFC led to an output power density enhancement greater than 2.5 times. With an anodic aluminum oxide (AAO) porous support structure, an ALD GDC thin film SOFC (TF-SOFC) showed a high power density of 288.24 mW/cm² at an operating temperature of 450°C.