一种矿山用钢筋网自动化焊接生产线的设计

设计一条钢筋网自动化焊接生产线，包括经料送料平台、纬料自动分料及上料机构、多点电阻点焊机、接料平台、卸料机械手。从上料到出料依靠电机、汽缸之间的协调工作来实现。并由单片机和PLC实现控制功能，上位机用MCGS组态软件在整个过程监视现场，采集工作状态及参数，起到监控作用。     

Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

A new alloy design concept for austenitic stainless steel with tungsten modification for bipolar plate application in PEMFC

The feasibility of a new alloy design concept utilizing the principle of ‘tungsten bronze effect’ is critically evaluated for the development of metallic bipolar plates for proton exchange membrane fuel cell (PEMFC). An austenitic stainless steel (ASS) is modified with W and La to improve the stability of the passive film in an acidic environment as well as to reduce the contact resistance by the tungsten bronze effect. The experimental ASS containing W and La was evaluated in a simulated PEMFC environment of H₃PO₄ and H₂SO₄ solutions at 80 °C, and the electrical property was evaluated by performing a contact resistance test. The test results show that the ASS modified with W and La has good passive film stability for corrosion resistance and low contact resistance. The X-ray photoelectron spectroscopy (XPS) analysis clearly suggests the possibility of the tungsten bronze effect from the change in valency state of W⁶⁺ to W⁵⁺ in the passive film formed on the modified ASS. The feasibility of a new alloy design concept utilizing the ‘tungsten bronze effect’ is well demonstrated; however, more study is highly required for the development of metallic bipolar plates of PEMFC.     

Evaluation of different coating systems by electrochemical methods

Corrosion protection of organic coated steel is determined by free corrosion potential measurements and impedance spectroscopy. The results are classified by means of very basic considerations and evaluation figures are developed. These electrochemical data are correlated with the extent of the corrosion for each coating system. The evaluation figures are used for ranking coating systems and this ranking is correlated with the ranking with reference to the results of standardized and exposure tests.     

用LG55冷轧管机轧制小直径不锈钢管孔型改进

介绍了ＬＧ５５冷轧管机使用Φ７～３２ｍｍ、Φ５０～３２ｍｍ孔型轧制小直径不锈钢管的工艺特点。试验表明，两种孔型可行，且Φ５７～３２ｍｍ孔型的综合使用效果更好。     

提高Cr12MoV钢冷作模具寿命的措施

从原材料改锻、预备热处理、淬火及回火、深冷处理、表面强化处理等方面分析介绍了提高Cr12MoV钢冷作模具寿命的一些方法和措施 ,并通过实例表明 ,采用这些方法和措施可较大幅度地提高模具寿命     

The generation of surface roughness during slurry erosion-corrosion and its effect on the pitting potential

Results of experiments performed to isolate the effect of surface roughness generated during slurry erosion-corrosion of 304L stainless steel are presented. Surfaces prepared by grinding to different finishes show that increasing the roughness lowers the pitting potential in chloride solution. Subsequent erosion by an aqueous sand slurry then alters this pitting potential (E_p), as measured in the solution phase alone, in a manner dependent on the initial surface roughness. Surfaces which were initially rougher show a pronounced rise in _p after erosion, while those with an initially smoother finish show a fall in E_p after erosion. Measurement of E_p during erosion-corrosion does not fit either process, with values of _Ep lower than those predicted from the surface roughness alone.     

Characterization of blasted austenitic stainless steel and its corrosion resistance

It is known that the corrosion resistance of stainless steel is deteriorated by blasting, but the reason for this deterioration is not clear. A blasted austenitic stainless steel plate (JIS-SUS304) has been characterized with comparison to the scraped and non-blasted specimens. The surface roughness of the blasted specimen is larger than that of materials finished with #180 paper. A martensite phase is formed in the surface layer of both blasted and scraped specimens. Compressive residual stress is generated in the blasted specimen and the maximum residual stress is formed at 50–100 μm from the surface. The corrosion potentials of the blasted specimen and subsequently solution treated specimen are lower than that of the non-blasted specimen. The passivation current densities of the blasted specimens are higher those of the non-blasted specimen. The blasted specimen and the subsequently solution treated specimen exhibit rust in 5% sodium chloride (NaCl) solution, while the non-blasted specimen and ground specimen do not rust in the solution. It is concluded that the deterioration of corrosion resistance of austenitic stainless steel through blasting is caused by the roughed morphology of the surface.     

Enabling factors toward production of nanostructured steel on an industrial scale

Utilizing the existing properties of steel, a modern technological society has been constructed. While there are over 25,000 worldwide equivalent steels based on manipulating the eutectoid transformation, there exist only a handful of commercial nanostructured steel alloys based on manipulating the more complex glass devitrification transformation. Thus, research on nanostructured steels is in its infancy, and many further developments are expected with the demonstrated promise of developing new combinations of superior properties. In this article, seven enabling metallurgical factors are presented that ultimately allow a variety of nanostructured steel products to be produced in an ever-increasing array of industrial processing techniques. Additionally, a case example of the formation of nanostructured steel are given showing how these factors can be harnessed on an industrial scale.