Optimal size,hydraulic retention time and volatile solids loading rate of biogas unit using water hyacinth

With a view to evaluate the effects of hydraulic retention time and volatile solids loading rate on methane production using water hyacinth, experiments were conducted in a 160 dm³ capacity, well-mixed continuous digestion unit at ambient temperature. The optimal design of biogas plant using water hyacinth was elucidated, to provide a unit giving a maximum methane yield of 0.16 nm³ kg^?1 volatile solids added, which was 60% greater than the conventional plant using cowdung. The calculations of optimal design factors were based on reactor size, hydraulic retention time and volatile solids loading rate; considerations were made of capital cost, running costs and operational revenue.     

Evaporation and Evolution of Suspended Solution Droplets at Atmospheric and Reduced Pressures

Thermal history and solute precipitation behavior of suspended solution droplets of sodium chloride (NaCl), magnesium sulphate (MgSO₄), and zirconium hydroxychloride (ZrO(OH)Cl) evaporating at atmospheric and reduced pressures are studied. Experimental measurements on the variation of droplet diameter, solution concentration, and temperature during the evaporation period are presented and discussed. The results of solute precipitation behavior in solution droplets observed under an optical microscope are displayed and discussed. Results indicate that reducing the pressure (∼ 33 kPa) results in a change in the solution droplet evaporation rate, but the thermal histories of a particular solution droplet are similar at the atmospheric and reduced pressures. At atmospheric and reduced pressures used in this study, the d² law for solution droplets is valid at early stages of the evaporation and before the solute precipitation initiates. Drying of MgSO₄ and ZrO(OH)Cl solution droplets results in the formation of spherical particles, whereas drying of spherical NaCl solution droplets results in the formation of cubic particles.     

p,V, T and derived thermodynamic data for toluene,trichloromethane, dichloromethane,acetonitrile, aniline,and n-dodecane

Experimentally determined p,V,T data are reported for toluene, trichloromethane, dichloromethane, acetonitrile, aniline, and n-dodecane at 278, 288, 298, 313, and 323 K, except for dichloromethane, for which the highest temperature was 298 K. At each temperature, measurements were done at pressures up to about 280 MPa or (for aniline and n-dodecane) at a lower pressure slightly below the freezing pressure at the temperature of measurement. Values of the isobaric expansivity isothermal compressibility and (for toluene, trichloromethane, dichloromethane, and acetonitrile) internal pressure, derived from the p,V,T data, are presented.     

壳体理论在水压爆破中的应用

在壳体理论的基础上,考虑到薄壳型结构水压爆破的特点,提出了一种新的药量计算公式,并得到了初步实际工程验证.     

物探螺旋钻机钻杆液压夹紧机构的设计计算

利用ANSYS大型有限元分析软件,对新设计的物探螺旋钻机钻杆液压夹紧机构进行了数值模拟分析计算。分析计算结果表明,当钻杆液压夹紧机构的钳体材料选择ZG310-570,所用液压马达的排量为390 mL/r时,该系统在最小驱动压力4.82 MPa、最大驱动压力7.30 MPa时才能正常工作。这种数值模拟分析为进一步改善钻杆液压夹紧机构的受力,改进机构的设计提供了依据。     

高压低温先导式安全阀的设计

介绍了一种某试验系统用高压低温先导式安全阀,主要从工作原理、结构特点、材料的选用、结构特点、试验等方面进行阐述。     

55t/h锅炉技术改造成功经验

介绍了35t／h锅炉扩容改造为55t／h非标锅炉的技术成功经验。从增加锅炉的容积、受热面面积、燃烧器喷嘴改造三个方面介绍了对锅炉本体的改造，改造后实现了锅炉的水位、汽温及燃烧自动调节，提高了锅炉的热效率为以后的锅炉扩容改造提供了实践经验。     

利用测井资料预测塔河油田地层破裂压力

针对塔河油田奥陶系碳酸盐岩油藏 ,介绍了地层破裂压力预测和地层裂缝高度预测的基本原理 ,选择了塔河油田 4口井的资料进行了破裂压力和裂缝高度预测的成果处理。为塔河油田奥陶系碳酸盐岩储层改造提供了较为可靠的施工参数     

Case Study of an Aerosol Explosion and a Method to Determine Explosion Temperatures

A failure analysis case study is presented for a two-piece aerosol containing tetrafluoroethane, commonly referred to as Refrigerant 134a. A gentleman was preparing to recharge the air conditioning system of an automobile when the bottom exploded off the aerosol container, propelling the body of the aerosol container like a rocket, which hit the man in the eye and blinded him in that eye. The aerosol was never connected to the air conditioner, therefore backpressure from the air conditioner (AC) compressor was ruled out as a cause for the explosion. The objective of the study was to determine why the aerosol exploded. Several recently developed test methods were used, including two types of heat-to-burst tests and a puncture chamber to measure the pressure-versus-temperature behavior of aerosols. More common test methods were also used, such as water bath pressure tests, hydro pressure burst tests, pneumatic pressure burst tests, hardness measurements, weight measurements, metallography, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), and an accident scenario recreation. A semi-empirical correlation between the hardness and weights of the container bottoms was used to determine the explosion temperature and/or pressure. This semi-empirical correlation agrees in principle with an analysis of the explosion pressures using finite-element analysis (FEA). The root cause for the explosion was determined to be a lack of strength of the bottom of the two-piece aerosol coupled with heating the aerosol to temperatures significantly above room temperature.     

基于PLC的焦炉集气管压力专家控制系统

通过对焦炉煤气集气管压力系统的分析研究，提出基于专家系统的集气管压力协调控制方案，使得系统在传统PID控制的基础上，能够按照系统实际运行状况智能选择控制策略。全部系统基于西门子S7系列PLC构成，并采用PROFIBUS电缆组成总线型网络。