Superplastic behaviour of Ti-48at.%Al two-phase titanium aluminide compacts made from mechanically alloyed powder

An HIP compact of MA-processed powder having a nominal composition of Ti-48at.% Al was produced. The compact consisted of a large amount of TiAl(λ) and a small amount of Ti₃Al (₂), in a completely ultra-fine equiaxed grain structure. This two-phase compact showed typical superplastic deformation behaviour. A maximum elongation of 550% was obtained. A strain exponent, n = 2, and grain size exponent, p = 2, were determined from the results of a strain-rate-change test and a creep test at constant initial stress using samples having various grain sizes, respectively. The activation energy for creep, Q_c at constant stress was calculated to be 350 kJ/mole. It is concluded that the superplastic deformation mechanism of the material under study is grain boundary sliding controlled by lattice diffusion in the TiAl phase.     

HPVC／PP共混改性研究：Ⅲ低分子量反应性化合物作相容剂

采用低分子量反应性化合物作相容剂，即化学交联体系来改善ＨＰＶＣ／ＰＰ共混物的相容性。考察了在不同共混比下，不同化学交联体系对共混物力学性能的影响，并观察了共混物的微观形态。结果表明，采用低分子量反应性化合物作相容剂，共混物的拉伸强度提高，但冲击强度无改善。分散相尺寸减小，相间粘接得到改善。并比较了３种增容方法的效果，发现ＣＰＥ是ＨＰＶＣ／ＰＰ共混物的最佳相容剂。     

活塞式压缩机吸排气管道的振动与控制

阐述了活塞式压缩机吸、排气管道强烈振动的危害，分析了产生共振的原因，介绍了现场消减管道振动的有效措施。     

检修链在煤矿生产中的作用

机电事故严重影响企业的安全运行。国投新集二矿通过完善机电设备检修链的各个环节,最终实现了降低机电事故率的目标。     

40Cr钢复合热处理强韧化

用光学及电子显微镜(SEM.TEM)观察不同热处理的40Cr 钢的冲击及断裂韧性断口、及金相组织,阐明其间相互关系;断口结构可反映断裂特征,组织情况;细化晶粒提高强度、塑性和冲击韧性,但却减少脆断的特性距离 l 因而降低 K_(1c)模;减少碳(杂质)偏聚而使其呈较均匀地分布,从而减少可诱发塑坑的较粗大的碳(杂质)化合物的析出,即增加塑坑的间距 di 以及增加塑断组成物。从而都可增加断裂临界应变 ef,都可以提高 K_(1c)40Cr 复合热处理既靠先超高温淬、回火以减少碳(杂质)偏聚,改善其分布,以反增加位错马氏体从而提高 K_(1c),也靠后淬、回火细化晶粒而提高强度、塑性和冲击韧性,各自发挥长处达到强韧化。     

奥氏体化温度对含稀土半钢力学性能的影响

研究了奥氏体化温度对含稀土半钢力学性能的影响 ,结果表明 ,半钢的冲击韧度 (αK)、抗弯强度 (σbb)和相对韧性 (σbb× f )随奥氏体化温度的变化较明显 ,而硬度 (HRC)受奥氏体化温度影响较小 ,当奥氏体化温度为 960℃时 ,其综合力学性能最佳     

Cold Gelation of β-lactoglobulin in the Presence of Iron

ABSTRACT: To protect and transport iron, we investigated the trapping properties of a network formed from β-lactoglobulin. We studied the influence of different parameters—pH, iron, and protein concentrations—on gel properties (optical and mechanical properties, WHC, and microstructure). For all conditions tested, the results show the formation of a cold gel in the presence of iron. The mechanical properties reveal that the elastic behavior and the strength of rupture increase with higher protein concentrations and decrease with higher iron concentrations. The water-holding capacity is high for low iron concentrations. The microstructure shows that, at low iron/protein ratios, a homogeneous filamentous network is obtained whereas, at high iron/protein ratios, more random aggregated particles are present.     

DRYING OF GRANULAR PARTICLES IN A MULTISTAGE INCLINED FLUIDIZED BED WITH MECHANICAL VIBRATION

A mathematical model for the drying rate of granular particles in a multistage inclined fluidized bed(IFB) is presented from the standpoint of simultaneous heat and mass transfer, with taking the effect of mechanical vibration added vertically into consideration.

Steady-state distributions for the temperatures and concentrations of the particles and the heating gas, and for the moisture content of the particles are numerically calculated based on the present model. The calculated results show fairly good agreement with the experimental data, which were obtained from the drying experiments of brick particles in a three-stage IFB using comparatively low temperature air(40-60°C) as the heating gas.

It has been found within the range of the experimental conditions employed that, the mechanical vibration added vertically enhances the over-all drying rate of the particles and its effect can be considered equivalent to an increase in the air velocity.     

Mechanical properties of poly(ether-ether-ketone) for engineering applications

An outline of the characteristics of PEEK and the versatility of its compositional forms (micro and macro composites) are given to illustrate its wide potential for success in engineering applications. Although it is necessary to have particular tabulations of mechanical properties for engineering design, these are seldom available and consequently it is argued that an understanding of stiffness, toughness and strength properties are required to fully exploit available manufacturer's data and thus develop the full potential of PEEK and its composites. Stiffness characteristics are considered in terms of a modulus function which is dependent on time under load and temperature. In its composite forms, whether reinforced with short or continuous fibres, stiffness anistropy can be both considerable and complex, but some empirical ground-rules are apparent. For continuous fibre composites even in the form of complex lay-ups, it is also possible to attempt some stiffness prediction from certain pseudo-elastic constants. Toughness of PEEK and its composites is described in terms of both comparative and intrinsic properties. Instrumented falling weight impact data, particularly as a function of temperature enable some insight into ductile-brittle transitions for the unreinforced material, but crack initiation and crack propagation processes for the various fibre reinforced forms. Intrinsic toughness is described in terms of linear elastic fracture mechanics theory. Strength properties are described for static and dynamic loading configurations. In particular, PEEK and its composites are evaluated for increasing test severities for strength characteristics; stress concentration, loading form and test temperature are considered.     

岩石工程力学特性参数测定装置设计

岩石工程力学特性参数测定装置实现了对试验载荷的恒速率加载 ,可对压模的吃深和试验载荷进行连续记录 ,记录的数据可实时显示及处理 ,且动态显示试验岩石的特性曲线 (试验载荷—轴向应变 )。该装置体积小、可移动性强 ,且能一机多用。文章详细阐述该装置机械结构、电路和系统软件的设计等