WC对Cu/WC_P复合材料性能及组织的影响

通过ＷＣ含量对ＷＣ／Ｃｕ复合材料性能的影响，确定了冷压－烧结法制备Ｃｕ／ＷＣ材料的适宜ＷＣ含量为１０ｖｏｌ％左右。并就ＷＣ对该材料组织和再结晶行为的影响进行了有益的探讨。     

Stabilization of inter-area and/or oscillatory modes in large-scale power system by voltage impedance power system (VIPS) apparatus based on decentralized control scheme

New technologies such as power electronics have made it possible to change continuously the impedance of a power system not only to control power flow but also to enhance stability. A power system incorporating a variable impedance apparatus such as a variable series capacitor (VSrC) and high-speed phase shifter (HSPS) is called VIPS (Variable Impedance Power System) by the authors. This paper proposes a novel control method of VIPS apparatus such as VSrC and HSPS installed at an interconnecting point for stabilizing inter-area unstable and/or oscillatory modes. The proposed design method of the control system is a kind of hierarchical decentralized control method of a large-scale power system based on a Lyapunov function. Under the proposed control scheme, each subsystem can be stabilized independently by local controllers such as AVR, speed governor and PSS, and then the whole interconnected system can be stabilized by VIPS apparatus taking into account interactions between subsystems. The effectiveness and robustness of the VIPS apparatus control are shown by numerical examples with model systems including a large-scale power system.     

高速冷带轧机垂直自激振动稳定性分析的数值计算方法

本文在充分考虑轧机垂直振动过程中辊缝非线性的基础上，利用轧制理论方程和机械振动理论中的能量判据，给出了更精确的分析高速冷轧机垂直自激振动稳定性的数值计算方法。     

Corrosion fatigue short crack growth behaviour in a high strength steel

The influence of an aggressive environment (0.6 M, aerated NaCl solution) on short fatigue crack initiation and growth behaviour has been studied. The study involved three major test series, namely: air fatigue, corrosion fatigue, and intermittent air fatigue/corrosion fatigue. The above tests carried out under fully reversed torsional loading conditions at a frequency of 5 Hz, showed that it was the non-metallic inclusions which took part in crack initiation resulting from debonding at metal matrix/inclusion interface and pitting of inclusions in both air and corrosove environments, respectively. Short fatigue crack growth results in these two environments obtained by using plastic replication technique, indicated a large effect of microstructure i.e. prior austenite grain boundaries. The stage/stages at which the environmental contribution was dominant has been discussed by considering the results achieved from intermittent tests. However, the mechanisms involved in corrosion fatigue short crack growth have also been described in the light of results obtained from futher investigations carried out by conducting corrosion fatigue tests under applied cathodic potential conditions and tests on hydrogen pre-charged specimens under air fatigue and uniaxial tension conditions.     

低合金高强度钢的微观组织和疲劳裂纹扩展行为

用透射电镜观察了３０ＣｒＭｎＳｉＮｉ２Ａ钢等温的微观组织，疲劳裂纹扩展行为、裂纹尖端塑性区和位错结构，结果表明，等温状态组织由马氏体和贝氏体组成。在一个奥氏体晶粒内一般存在四个板条领域、裂纹尖端的塑性区内存在主位错带，疲劳断裂的基本组织单元为板条晶或板条束。裂纹遇到板条束界时方向发生较大偏斜。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

线性时变系统的区间稳定性与鲁棒稳定性

本文应用向量比较定理研究线性时变系统的区间稳定性和具非线性时变摄动的线性时变系统的鲁棒稳定性，所得的新结果包含文献的一些主要结果作为特例，本文的研究方法说明向量比较方法是分析区间稳定性和鲁棒稳定性的一种自然而有力的工具。     

Pi-coefficient analysis of update algorithms for adaptive systems

This paper finds the appropriate pi-coefficients for a parameter estimation adaptive system and uses them to analyze the stability of two estimation algorithms. The estimation error dynamics of the system are modeled by a linear time-invariant subsystem and a nonlinear time-varying update law in a feedback loop. Then the so-called max-p problems are formulated and solved to obtain the pi-coefficients for the linear subsystem and nonlinear update low. For the investigated system, the quantitative results show that the least-squares update algorithm has larger stability range than that of the gradient algorithm, and the σ-modification scheme gives larger stability ranges for both algorithms.     

β－C_2S固溶体稳定的热力学研究

从热力学理论出发，利用Ｘ射线衍射定性和定量的方法，对β－Ｃ＿２Ｓ固溶体的稳定性进行了分析和研究。经热力学理论推导得出β－Ｃ＿２Ｓ稳定的热力学条件，即掺入的微量元素的化学位μ＿ｉ须小于β－Ｃ＿２Ｓ的反应自由焓△Ｇ＿β，μ＿ｉ＜△Ｇ＿β．并定量地计算出一种微量元素稳定β－Ｃ＿２Ｓ的临界掺加量为；多种微量元素对β－Ｃ＿２Ｓ的稳定性判断条件为：     

The effect of structural features on mechanical properties of loose optical fiber poly(butylene terephthalate) tubes

Results of a study on the modifying mechanical properties of loose optical‐fiber poly(butylene terephthalate) (PBT) tubes, produced during the standard industrial extrusion process, show that heat treatment make the structure of their material to change. The study comprised measurements of mechanical strengths properties of the tubes (tensile strength, compression strength, kinking) and determination of tube material structure [by differential thermal analysis (DTA), wide angle X‐ray scattering analysis (WAXD), and scanning electron microscopy (SEM)]. Results of the study allowed observation that the annealing at 70°C for 34 h of the tubes caused the crystalline α phase to increase in the tube material from ～28.5% to ～31.5% and the structure of the existing crystallites to become more perfect. This made the values of certain mechanical properties of the tubes to increase even by as much as 30%. The tubes following such thermal treatment could be used in cables exposed to heavy‐duty operation in arduous environments, where a larger margin from the standpoint of mechanical properties is required. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2130–2134, 2002