串扰耦合的低频分析有效性及阻抗特性研究

从传输线模型出发，分析了二平行直导线间串扰的低频模型有效性，得出允许3dB误差的条件下，低频模型在工程计算串扰中的电学短线和频率足够小的具体限值；同时分析了端接阻抗大小对串扰耦合的影响。对电磁兼容性中的串扰耦合的工程应用有实际指导和参考意义。     

Effects of calcination temperature on phase and microstructure evolution of BaTi4O9 powders

Calcining of the mixture of BaCO₃ and TiO₂ with a ratio 1:4 at different temperatures was carried out to synthesize BaTi₄O₉ powders. Phase evolution of the samples was studied using the differential thermal analysis (DTA) and X-ray diffractometry (XRD). Both techniques confirmed that the formation of BaTi₄O₉ started around 1000 °C. The XRD peaks showed that BaTi₄O₉ was most pronounced at 1250 °C. X-ray line broadening methods were employed to study the variation of particle size and microstrain of the BaTi₄O₉ powders. The Voigt function in a single line and the pseudo-Voigt function in the variance methods were used in our case. We found that both functions resulted in the same trends, i.e., the particle size increased with the temperature with the biggest size of 180 and 160 nm, whilst the microstrain yielded the opposite trend with the lowest values of 6.2 × 10^–3 and 1.1 × 10^–3. The scanning electron microscopy (SEM) study revealed the size of the large particles formed, due to agglomeration, to be about 0.5–1.9 μm. Furthermore, it was shown that irregular shapes of BaTi₄O₉ powders necked to each other appeared at 1000 °C and grew into ellipse and rod shapes at 1250 °C. Electronic Publication     

耐高温绝缘GFRP管的真空辅助树脂传递成型工艺研究

阐述了耐高温绝缘GFRP管的成型工艺及原材料选择，并对影响成型工艺的主要因素作了理论分析及试验验证。研究表明，以TDE－85／DDS体系为为基体，以无碱无捻玻璃纤维方格布为增强材料，用VARTM工艺成型的石油勘探高性能平衡管完全满足技术要求。     

光纤专用网中基于DSP的Q值在线检测模块的设计

基于误码率与Q值的对应关系，本文介绍一种Q值在线检测方法，模块设计采用DSP技术，并讨论了该模块在光纤工业专用网（FIN）中的应用。     

射频MEMS压控电容器

研究了射频 MEMS压控电容器的设计和制造工艺。压控电容器的制作采用了 MEMS制造技术 ,其主要结构为硅衬底上制作金属传输线电极和介质层 ,然后制作金属膜桥作为电容器的另一个电极。通过改变加在金属膜桥与传输线间的电压达到改变电容值的目的。这种压控电容器可以工作于射频和微波波段 ,具有很高的Q值。测试结果如下 :在 1 GHz、0 V时 Q值达到 3 0 0 ,0偏压电容值为 0 .2 1 p F,当加上驱动电压后 Cmax/ Cmin的变比约为 4∶ 1     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

Structure and properties of injection‐molded polypropylenes with different molecular weight distribution and tacticity characteristics

Two series of polypropylenes with different molecular weight distribution and tacticity characteristics were injection molded into flexural test specimens by varying cylinder temperature and the effects of the molecular weight distribution and tacticity on the structure and properties of the moldings were studied. Measured propertied were flexural modulus, flexural strength, heat distortion temperature, Izod impact strength, and mold shrinkage and structures studied were crystallinity, the thickness of skin layer, a*‐axis‐oriented component fraction and crystalline orientation functions. The relations between the structures and properties were also studied. It was found that the molecular weight distribution and tacticity characteristics affect the properties mainly through the molecular orientation and crystallinity, respectively. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 2142–2156, 2002     

计算机辅助设计中浓淡曲线的设计

本文介绍利用Super Frame软件进行色彩浓淡设计的原理、方法和步骤。据此原理和方法,使用C语言设计开发出了应用实例——折线浓淡分布曲线。     

Electrochemical impedance spectroscopy of a free-standing oxide film

The corrosion of low carbon steel in natural sea-water is characterized by the formation and growth of compact and thick layers composed of oxides, insoluble salts and organic materials. These layers are the result of corrosion processes induced by local environmental conditions, water oxygen supply; ionic species; bacteria and organic matter. The exchange of various species (ions, molecules, gas) between sea-water and the rust layers or the metal depends both on the kinetics of the Faradaic reactions of the entities with either the oxides or the metal, as well as on their transport properties through the different strata of the rust layers. In this work, an impedance study was carried out using the 4-electrodes cell arrangement with corrosion products picked up on steel sheet piling immersed for 25 years and analyzed as free standing membranes. This new approach is a good way to reach the specific transport and transfer properties of the oxide without being blurred by the metal influence. The physical model developed in this work was based on a transmission line, and accurately described the experimental diagrams. The electronic resistivity of the oxide layer, its porosity, the mean pore size and the reaction kinetics parameters could be determined from the fittings.     

Sensorless control of synchronous reluctance motors using on‐line parameter identification method not affected by position estimation accuracy

This paper presents a novel on‐line parameter identification method for sensorless control of Synchronous Reluctance Motors (SynRMs). Although conventional sensorless control methods based on mathematical models usually need some complex measurements of motor parameters in advance, the proposed identification method does not require them and can be realized on‐line. The proposed method identifies motor parameters under sensorless control, so rotor position and velocity cannot be used to identify these parameters. However, the proposed method does not need rotor position and velocity, and identified parameters are not affected by these estimation errors. The sensorless control using identified motor parameters is realized, and the effectiveness of the proposed method is verified by experimental results. © 2006 Wiley Periodicals, Inc. Electr Eng Jpn, 155(3): 62–69, 2006; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20258