市县HFC系统如何选择和使用光端机

对有线电视工程设计中如何选用优质设备、提高网络质量等问题进行探讨     

Extremes of random fields over arbitrary domains with application to concrete rupture stresses

To find the exact probability distribution of the global maximum or minimum of a random field within a bounded domain is a pending problem even for Gaussian fields. Except for very special examples of fields, recourse must be taken to approximate reasoning or asymptotic considerations to be judged with respect to accuracy by simulations. In this paper, the problem is addressed through a functional equation that leads to the definition of a class of distribution functions that depend solely on process or field characteristics and domain quantities that can be calculated explicitly. This distribution function class is studied for Gaussian processes in earlier works by the author and it has been obtained explicitly for Gaussian fields on rectangular domains in the plane. Simulation studies show that rather good predictions are obtained for sufficiently smooth wide band Gaussian processes and fields. In this paper, the distribution function is obtained in general for Gaussian fields over arbitrary bounded domains with piecewise continuous and differentiable boundaries, and as in earlier works the distribution function is tested against empirical distribution functions obtained by simulation of sample functions of a smooth approximately Gaussian field, herein called a broken line Hino field. For completeness this particular field type is defined in appendix a and appendix b. The paper concludes with a statistical application on data for plain concrete tensile strength.     

一个基于优化的有限元模型修正方法

本文提供了一个基于一阶搜索优化的有限元模型修正方法。它只需利用结构模态试验的部分固有频率，就能获得较精确的有限元模型。文中附有某无人机上垂尾有限元模型修正的实例。根据上垂尾前二阶试验的固有频率，采用本文方法，对有限元模型进行了修正。修正后有限元模型的前二阶固有频率与试验值的相对误差在2．35％以内，而第三阶固有频率与试验值的相对误差仅为5．81％。它不仅大大地缩小了用修正前有限元模型算得的固有频率与试验值的相对误差，而且还能较精确地预测无试验结果的高阶固有频率值。     

Numerical Filling Simulation of Injection Molding Using Three-Dimensional Model

1 Introduction During injection moulding, the rheological response of polymer melts is generally non-Newtonian and nonisothermal with the position of the moving flow front. Because of these inherent factors, it is difficult to analyze the filling process. Therefore, simplifications usually are used. For example, in middle-plane technique and dual domain technique [1], because the most injection molded parts have the characteristic of being thin but generally of complex shape, the Hele-Shaw …     

气象图数据的提取与转换

对气象图中等值线数据的提取与转化问题进行了研究 ,其中包括图像的二值化、细化、矢量化以及提取数据的转换和还原。它为从已有的气象图像资料中获得数据资料提供了一条有效的途径     

沉降路段供水管线穿越障碍方法探讨

结合工程实际 ,对市政沉降路段上的给水压力管线 ,如何穿越障碍 ,减少不均匀沉降提出了具体的措施及相应建议     

声表面波32位MSK抽头延迟线

介绍了扩频通信有效的ＭＳＫ信号特点及声表面波ＭＳＫ抽头延迟线构成方式，给出了声表面波３２位ＭＳＫ抽头延迟线的实验结果。     

核孔膜生产线膜微孔制备工艺实验研究

本文介绍核孔膜生产线,重点描述了膜微孔制备工艺的实验研究。对于PC和PES膜,已得到32种工况下的扩孔公式,其形式为D=A+Bt,其中D——孔径,t——扩孔时间,A,B为特定工艺参数下的常数值.通过实验。得到了膜孔密度N与300~#核反应堆功率P、热柱辐照位置L的经验公式,即N=6.97×10~5×10~3×101~(1.18L).在本生产线上可生产最大幅面为3 140mm×240mm,孔径为0.04～10 μm的多系列多规格的核孔膜产品。     

冷轧厂酸洗机组3号横剪大流量中高压液压系统设计方案探讨

在宝钢２０３０ｍｍ冷轧厂酸洗机组中，为了满足厚规格ＩＦ钢的生产，拟将原有的气动式剪切机改成液压式剪切机。为此，设计了一套中高压大流量的液压系统以满足３号横剪大剪切力（最高达７００ｋＮ）和快速剪切（３秒／次）的需要。由于采用了蓄能器增速回路和二通插装阀控制技术，使该液压系统较传统的剪切机液压系统具有响应速度快、体积小、重量轻、发热少和降低电机能耗等优点。     

Φ76mm自动轧管机组穿孔机顶杆小车的改进

通过校核Φ７６ｍｍ自动轧管机组穿孔机顶杆小车的轴承寿命，提出了顶杆小车的改进措施，如重新选配合适的轴承型号，修改有关装配尺寸等。改进后，顶杆小车的使用效果良好。