Surface Areas of Nitrated Hydrotalcites

Hydrotalcites in the nitrate form were prepared using microwave irradiation in the hydrotreatment step. The surface area (BET) of nitrated hydrotalcites was evaluated. Solids were characterized by atomic absorption, X-ray diffraction and BET analysis. Thermal pretreatment temperature determined the surface area of the hydrotalcites.     

Thermodynamic Criteria for the Maximum and Minimum Strength of Fibre-Reinforced Composite Materials

The overall performance and reliability of composite materials are, in most cases, dependent upon the behaviour of the reinforcement-matrix interface, particularly upon its ability to transfer stress.

A theory for predicting thermodynamic conditions for the maximum and zero-adhesion at the reinforcement-matrix interface is tested in this paper, based on experimental data. Proposed is a model of the relationship between mechanical properties of composite materials (tensile strength, flexural strength, Young's modulus and impact resistance) and energetic properties of matrix and reinforcement expressed by the energy ratio a = γ_l/γ₂.     

Thermoelectric properties of SbNCa3 and BiNCa3 for thermoelectric devices and alternative energy applications

Thermoelectric properties of two antiperovskites SbNCa₃ and BiNCa₃ are calculated using first principles calculations. High values of Seebeck coefficients are observed for these materials. Electrical and thermal conductivities are also calculated. Increase in thermal conductivity and decrease in electrical conductivity are found with increasing temperature. The maximum values of thermal conductivity are 92×10¹⁴  W/m K s and 88×10¹⁴  W/m K s for SbNCa₃ and BiNCa₃ respectively at a temperature of 900 K. The peak values of 5×10²⁰/Ω m s and 5.2×10²⁰/Ω m s are achieved for n-type SbNCa₃ and BiNCa₃ respectively at a temperature of 300 K. Figure of merit is achieved for these materials at room temperature which shows that these materials can be useful for thermoelectric devices and alternative energy sources.     

Characterization of microporous-mesoporous MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide

MCM-41 silicates prepared in the presence of octyltrimethylammonium bromide either by a conventional method or by post-synthesis hydrothermal treatment were characterized by nitrogen adsorption in a wide range of relative pressure from 10^-6 to 1. Hydrothermally restructured samples were found to have lower BET surface areas, lower external surface areas and thicker silica walls than the non-treated sample. More importantly, in addition to their characteristic mesopores (ca. 3 nm), they were shown to have considerable amounts of micropores. The relative amount of micropores and mesopores was shown to be dependent on the treatment conditions. Thus, it is demonstrated that the postsynthesis hydrothermal restructuring is a convenient synthesis route to MCM-41 silicates with bimodal pore size distribution involving controllable amounts of microporosity. This revised version was published online in July 2006 with corrections to the Cover Date.     

Use of mesoporous SBA-15 for nanostructuring titania for photocatalytic applications

SBA15–TiO₂ samples prepared by introducing titanium with a grafting method and having TiO₂ loadings below 15 wt.% have been characterized by XRF, XRD, IR, porosimetry, SEM, HRTEM, and UV–Visible diffuse reflectance. Differently from the samples reported in the literature characterized by a high TiO₂ loading, no evidences have been found for the presence of titania particles inside or outside the mesopores of SBA-15. Three different titanium species were instead evidenced to be present. The first two derive from the reaction of titanium with silanol groups in the corona area of inner SBA-15 walls leading to the formation of either TiO₄ tetrahedral sites (by reaction by hydroxyl nests of surface defect sites) and/or pseudo-octahedral surface sites anchored by two (or more) Si or Ti ions through bridging oxygens. The third species derives from the reaction of titanium in the regions with high sylanol density, e.g. in the micropores located in the corona of SBA-15 channels, leading to the formation of TiO₂-like nanoareas (probably Si-doped) with dimensions of around 1–2 nm maximum. The potential interest of these materials as photocatalysts, for the presence of a TiO₂-like nanoareas highly accessible by reactants, is discussed.     

A polyamide-silica composite prepared by the sol-gel process

Summary A new kind of organic-inorganic hybrid composite was prepared by means of the sol-gel process. The polymer employed was a mixed-isomer aromatic polyamide having good solubility and thermal stability. The silica constituting the inorganic phase was produced by the hydrolysis and condensation of tetramethoxysilane. The bonding between the phases involved aminophenyl-trimethoxysilane, in which the amino group can react with the phthaloyl chloride end-capped polymer, and the methoxysilane groups undergo hydrolysis. The composition of these composites was varied by changing the linear polymer chain length and relative amount of tetramethoxysilane. The gelation time was found to range from a few minutes to several days. Thermogravimetric analyses showed that decomposition starts at approximately 450 °C. Thin films cast from materials having a relatively high silica content were opaque and rigid, but those with low silica content were flexible and transparent.     

基于电子印刷工艺的薄膜热电偶研制

薄膜热电偶由于具有体积小、热容量小及响应速度快等优点成为近年来学者们研究的重点。薄膜制备常用的方法有射频溅射法、离子镀膜法以及直流脉冲磁控溅射法等,但这些方法操作设备复杂,制作时间长,效率低,成功率低且复现性差。用电子印刷工艺制备薄膜热电偶,将Au,Pt的溶液化微纳米材料印制在基板上,印刷成为Au-Pt薄膜热电偶,该方法操作方便快捷,对电极材料污染小。通过试验证明:采用电子印刷工艺制备的Au-Pt薄膜热电偶符合Au-Pt热电偶检定规程的要求,热电偶精度高,重复性和一致性好。     

熔融石英耐火材料

阐述了熔融石英耐火材料的主要性能与应用领域。     

MgO／Ni系梯度功能材料的设计与制备

对ＭｇＯ／Ｎｉ系梯度功能材料（ＦＧＭ），分别用实验和微观力学模型测定和计算了用于热应力缓和设计的各物性参数。讨论了两种结果之间存在差异的原因。用有限元方法模拟了制备过程中ＦＧＭ的热应力，得到ＭｇＯ／Ｎｉ系ＦＧＭ的综合设计准则。按设计结果进一步调整粉末工艺性质，成功地烧制出ＭｇＯ／Ｎｉ系ＦＧＭ。