（RbCl）108离子簇均相成核的分子动力学研究

分子动力学模拟测得熔融（RbCl)108离子簇在300K至600K温度时凝固的成核速率大于10^35m^-3s^-1,用均相成核的经典理论加以分析,估算得氯化铷离子簇的固液界面自由能σalT^1.4,用Grunasy提出的扩散界面理论加以分析,估算得扩展界面厚度约为0．195nm,σalT^0.97,2个理论在实验温度范围内没有明显判别,且均能较好地分子动力学模型的结果,但预测的较高温度下的成核速率有比较显著区别,因此进一步地研究将有助于鉴别它们。     

Mineral admixtures in mortars: Effect of inert materials on short-term hydration

This work is the first part of an overall project the aim of which is the development of general mix design rules for concrete containing different kinds of mineral admixtures. The separation of the different physical effects responsible for the modification of cement hydration, when chemically inert quartz powders are used in mortars, is presented. The phenomenological approach, based on semi-adiabatic calorimetry, is only associated with first-order phenomena, and the study excludes the complex physicochemical details involved in the chemistry of cement. The results, obtained for a wide range of fineness (between 180 and 2000 m²/kg) and replacement rates (up to 75%), show that short-term degrees of hydration in mortars containing a chemically inert mineral admixture (quartz) are always higher than for a reference mortar. This study confirms that cement hydration is enhanced by inert mineral admixtures. The two main physical effects responsible for the modification of the hydration of cement are identified as the dilution effect and heterogeneous nucleation. The dilution effect of the cement is highlighted with a coarse mineral admixture. The heterogeneous nucleation effect, although it increases with fineness of mineral admixtures, presents an optimum depending on the replacement rate. In the following part of this work, these results will be used for the development of an empirical model allowing us to quantify both physical effects.     

Mechanism and Inhibition of Grain Coarsening of Al-Mg-Si Alloy in Hot Forming

A high-Ti 6061 alloy was rolled with strains up to 0.8-2.0 and at 350-550 ℃. Microstructures that developed during deformation and subsequent solution heat treatment (SHT) were observed by using optical and transmission electron microscopy. Microstructure evolution during SHT depends mainly on the initial rolling temperature, and it was found that the higher this temperature is, the coarser the grains are. After rolling at 400 ℃, well-defined cells and subgrains were formed, which induced further sites for recrystallization nucleation during subsequent SHT. The recrystallization mechanism was found to be subgrain rotation, with a final grain size smaller than 200 μm. Increasing the rolling temperature to 500 ℃ results in a low density of dislocations distributed uniformly in the deformed matrix and fewer nucleation sites during subsequent SHT. The recrystallization mechanism is grain boundary bulging, while the final grain size approaches several millimeters. Finally, a hot forming process of high-Ti 6061 alloy for inhibiting grain coarsening was proposed, and verified by experiments.     

Fatigue cracks nucleation on steel, acoustic emission and fractal analysis

In this paper, a new acoustic emission (AE) diagnostic technique, for the study of fatigue cracks nucleation and propagation on steel, was investigated. Using the fractal analysis, and the box-counting method (BCM) in particular, it is possible to characterize the spatial distribution of the prime AE sources through the fractal dimension (D) that evolve with the number of fatigue cycles (N) of the specimen. D–N curves were found useful to identify the condition of incipient collapse due to the nucleation and propagation of fatigue cracks on steel. It is possible to use the fractal dimension as a damage parameter. In all tested specimens, the crisis occurs within the same range of values of fractal dimension. The results suggest that it is possible to anticipate the detection of crack beginning relating to the other theoretical or experimental techniques.     

Prediction of the crack extension under fretting wear loading conditions

Fretting is associated with small amplitude oscillatory movements between two surfaces in contact. One possible consequence of fretting is the formation and subsequent growth of cracks at the edges of the contact. This paper presents an experimental investigation of the cracking behaviour under fretting loading of two different aluminium alloys: 2024-T351 and 7075-T651. Systematic and controlled experiments with a cylinder-flat contact under partial slip fretting conditions were carried out. A model which combines both crack nucleation and propagation processes is used to predict the crack extension throughout the life of the component. The direction of crack propagation experimentally observed was taken into account by the model. Furthermore, an analytical prediction of crack nucleation based on the process volume approach is made. The predictions of both crack extension and nucleation are compared with the experimental results, and show good agreement.     

微合金钢等温沉淀析出动力学模型

采用形核长大模型对高强度低合金钢中的微合金元素铌、钛和钒的等温析出行为进行了定量计算,把计算结果与等温应力松弛实验结果相比较,分析产生计算误差的原因,为连续冷却的析出计算提供依据.     

Coating of SiC Powder with Nano YAG Phase

SiCceramiccompositeshavefoundextensiveap plicationsinmodernindustryduetotheirexcellentchemicalstabilityandwear resistance .Rodeghieroetal.[1～ 3 ] investigatedthefabricationofSiC Al2 O3 ce ramiccompositematerialsviaco precipitationcoatingandsol gelmethods…     

Metallurgical Development in Steel‐plant‐internal Multi‐injection Hot Metal Desulphurisation

The use of thermodynamic, statistical, and light and electron‐optical microscopic methods has made it possible to analyse the course of reactions during steel‐plant‐internal hot metal desulphurisation. The theoretical dependence between oxygen and sulphur activity has been used to develop an EMF‐measurement‐based technique for determining the sulphur content as the hot metal is desulphurised. The absence of magnesium sulphide from the collection of phases in the final slag because of the greater stability and secondary formation of calcium sulphide has been explained with the aid of thermo‐chemical calculations.     

Martensitic nucleation mechanism

A sort of special dislocation configuration was deformation-induced in an Fe-Ni-V-C alloy by in-situ elongation tests of TEM. The cooling in-situ observations, as well as the SADPs from the region of the special dislocation configurations, proved that they are martensitic nuclei. In martensitic transformation, a nucleus changed into a small martensitic sub-plate, and a group of parallel sub-plates that formed from a group of parallel nuclei made up a big martensitic plate Martensitic transformation involved opposite shear between adjacent martensitic nuclei. By using the reduced-cell method, the crystallographic structure of observed martensitic nuclei was indexed as a face-centered orthogonal (FCO) lattice, which was explained by the nucleation mechanism proposed by the present authors. The crystallographic analysis confirmed that the defect faulting involved in martensitic nucleation took place among three close pakked planes, instead of between two adjacent planes as an ordinary stacking fault.     

A study of the influence of grain boundaries on short crack growth during varying load using a dislocation technique

The propagation of short cracks in the neighbourhood of grain boundaries have been investigated using a technique were the crack is modelled by distributed dislocation dipoles and the plastic deformation is represented by discrete dislocations. Discrete dislocations are emitted from the crack tip as the crack grows. Dislocations can also nucleate at the grain boundaries. The influence on crack growth characteristics of the distance between the initial crack tip and the grain boundary has been studied. It was found that crack growth rate is strongly correlated to the dislocation pile-ups at the grain boundaries.