变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。     

电磁胀形磁场力的有限元分析

研究电磁胀形过程中工件受到的磁压力沿长度方向和厚度方向的分布是工件变形分析的基础。采用有限元方法对电磁胀形过程中作用工件上的磁场力进行了数值模拟。在磁场特性理论分析的基础上确立了模型的边界条件，得到了磁场力沿工件长度和厚度方向的分布规律。模拟结果与测量值基本吻和。     

冷成型模具低温锌系磷化

研制出适用于冷成型模具高硬度表面的低温锌系磷化工艺。其中磷化液含Zn(H2 PO4 ) 2 ·2H2 O 6 0g/L ,Zn(NO3) 2 ·6H2 O 90g/L ,NaNO2 1.5g/L ,稀土促进剂 0～ 1.0g/L ,游离酸度 4～ 6点 ,总酸度 70～ 75点。该磷化液在 4 0℃下 ,处理 30～ 4 0min后可获得厚约 10 μm的磷化膜。性能测试表明 ,其减摩、润滑性能良好 ,摩擦系数约降 0 .1,与未处理试样相比磨损量下降 96 % ,附着力 1级。     

Recrystallization/precipitation behaviour in microalloyed steels

Microalloyed high-strength low-alloy (HSLA) steels contain additions of Nb, V, Ti, or in combination, in amounts of 0.01 to 0.1 weight percent to improve mechanical properties, which are strongly dependent on the thermomechanical interaction taking place in the course of rolling mill processes. The recrystallizatian of hat-twisted austenite has been investigated in a cylindrical specimen (f 6×50 mm) machined from hat rolled plates of 0,052 wt % Niobium microalloyed steel. Continuous and interrupted torsion test were carried out in the temperature range 1123 K to 1173 K after a solution treatment of 1.5 minutes at 1423 K and torque-twist data were analysed. The various methods were discussed for obtaining results from torsion tests. The effect of precipitation kinetics was appreciated by way of connection t_p/t_p(red), where t_p is the experimental measured time for the peak stress and t_p(red) is the newly defined reduced time. The softening ratio X and time t_0.05R for start of static recrystallization were established.

The correlation between precipitation and recrystallization is presented as a graphs for chosen requirements (temperature of austenitization, carbon and niobium content and strain rate). If temperature goes below 850°C, the restoration processes are hardly suppressed, both are limited by diffusion and Nb(CN) precipitation, which are extended dynamically in the range of strains rates 10⁻² to 1 s⁻¹.

In the present paper, an attempt is made to derive the PRTT diagram and to define all mathematical equations for describing recrystallization times t_0.05R, t_0.5R, t_0.95R and t_0.05P for the start of precipitation. In real metal forming processes such as the hot rolling of plates or strips the knowledge of these parameters and results is extremely important for the the correct microstructure and sheet quality to be obtained.     

阵列天线在OFDM系统下行链路中的应用

正交频分多址(OFDM:orthogonal frequency division multiplexing)技术由于其在多径环境下克服码间干扰的固有特点,在移动通信中已得到广泛地应用。利用阵列天线上行链路信号到达角估计实时信息,计算OFDM系统下行链路阵列天线权重,将阵列天线应用于下行链路中,最后给出系统误码率性能的计算机仿真结果。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案     

枣35断块沙三段玄武岩储层特征及成藏条件分析

从地质、地震、测井及试油试采等方面入手，并采用新技术，对自来屯构造枣35断块沙三段玄武岩储层特征及成藏条件进行了分析。其结果为该区下一步勘探、开发及进一步研究奠定了基础。     

关于粉体成球机盘体几何形状的研究

通过对粉体小球在粉体成球机盘底上运动轨线的研究,利用Euler定理,结合其参数特点,得到了不同几何形状的盘底在成球过程中对粉体小球运动的影响,球面盘底较平面盘底更有利于成球的结论。     

翻领成型器领口曲线的程序计算展开法

根据翻领成型器领口曲线的数学模型，介绍一种利用计算器复杂公式存贮的特殊功能，预编程序计算相关参数。然后画领口曲线展开图的方法。     

变形温度和变形程度对Ti－31合金性能和组织的影响

通过高温和室温拉伸试验，研究了变形温度和变形程度对Ｔｉ－３１合金板材性能和组织的影响。结果表明，合金在７５０～８５０℃的温度下变形５％～２０％空冷后，其室温机械性能均能达到材料的技术指标要求。并发现了材料在９００℃的临界变形区。