Surface tailoring of an ethylene propylene diene elastomeric terpolymer via plasma‐polymerized coating of tetramethyldisiloxane

In the research presented here, we explore the use of a low‐energy plasma to deposit thin silicone polymer films using tetramethyldisiloxane (TMDSO) (H(CH₃)₂? Si? O? Si? (CH₃)₂H) on the surface of an ethylene propylene diene elastomeric terpolymer (EPDM) in order to enhance the surface hydrophobicity, lower the surface energy and improve the degradation/wear characteristics. The processing conditions were varied over a wide range of treatment times and discharge powers to control the physical characteristics, thickness, morphology and chemical structure of the plasma polymer films. Scanning electron microscopy (SEM) shows that pore‐free homogeneous plasma polymer thin films of granular microstructure composed of small grains are formed and that the morphology of the granular structure depends on the plasma processing conditions, such as plasma power and time of deposition. The thicknesses of the coatings were determined using SEM, which confirmed that the thicknesses of the deposited plasma‐polymer films could be precisely controlled by the plasma parameters. The kinetics of plasma‐polymer film deposition were also evaluated. Contact angle measurements of different solvent droplets on the coatings were used to calculate the surface energies of the coatings. These coatings appeared to be hydrophobic and had low surface energies. X‐ray photoelectron spectroscopy (XPS) and photoacoustic Fourier‐transform infrared (PA‐FT‐IR) spectroscopy were used to investigate the detailed chemical structures of the deposited films. The optimum plasma processing conditions to achieve the desired thin plasma polymer coatings are discussed in the light of the chemistry that takes place at the interfaces. Copyright © 2004 Society of Chemical Industry     

Asbestos replacement aspects: Modification of the fibre-matrix interphase in lonomer based composites

Asbestos fibres, of the chrysotile variety, and chopped carbon fibres were pretreated by an in-situ polycondensation technique eventually resulting in a polyamide coating on the fibre surface. Ionomer based composites containing either carbon or asbestos fibres in random in plane fibre orientation were prepared, and the influence of this coating process on the tensile properties was investigated. It was found that for the asbestos-filled composites the presence of the nylon 6,6 interlayer improves the tensile performance, especially at moderate polyamide depositions. This is not the case with the pretreated carbon-filled composites for which carbon fibres with higher polyamide contents are preferred. Combinations of the treated asbestos fibres with carbon and/or aramid fibres may be used to reduce the asbestos content in asbestos-only based engineering plastics.     

Development of cable fault location method using fiber optic distributed temperature sensor

When ground-fault problems occur on a cable line, immediate fault location and restoration are required. Therefore, various new methods to locate the fault point instantaneously have been investigated to replace such conventional methods as the Murray loop method and the pulse radar method [1]. These methods require a long time to locate the fault point. One possible fault location method is to sense the temperature rise following a ground fault using a fiber optic distributed temperature sensor. Application of this method was found feasible through sensing the temperature rise at a ground-fault test using a thermocouple as a temperature sensor with test cables [4]. A power/optical composite cable was prepared experimentally and after verifying its thermal mechanical performance, the temperature rise at an incidence of a fault was determined and the anticipated performance was demonstrated in a ground-fault test. This article describes the outline of the test.     

Nd3+ Doped Silicate Glass Photonic Crystal Fiber with Random Hole Distributions

The fabrication of one kind of large core area Nd3 doped silicate glass photonic crystal fiber, and demonstration of the fiber's waveguidence properties were reported. This fiber owns a random air hole distribution in the cladding. The measured minimum loss of this kind of fiber is 10 dB·m-1 at 660 nm. These fibers can sustain only a single mode at least over wavelength ranging from 660 nm to 980 nm.     

Role of Specimen Geometry in the Effect of Fiber Orientation on the Thermal Conductivity of a Uniaxial Carbon-Fiber-Reinforced Aluminoborosilicate Glass-Matrix Composite

A study concerning the effect of fiber orientation on the thermal conductivity of a uniaxial carbon-fiber-reinforced borosilicate glass was conducted. For thin specimens, and thick specimens with specimen sides cut parallel to the fiber direction, the dependence of thermal conductivity on fiber orientation showed excellent agreement with theoretical behavior predicted for a composite infinite in extent. In contrast, the thermal conductivity data for rectangular thick specimens fell well below the data for the thin and angled specimens. For fiber orientation of 45° and higher, at which the heat was directed toward the side of the specimen rather than across, the thermal conductivity values showed excellent agreement with theoretical behavior predicted for a finite composite strip with insulated sides.     

热分析在PVA纤维预处理中的应用

用差热、热重法对原丝的热性能及由不同预处理方法所引起的PVA纤维的热行为变化进行了研究;并通过模拟脱水条件,用不同升温速率,求出了经不同预处理纤维的脱水反应活化能。结果表明,PVA原丝在230℃有一软化点,三种预处理都不同程度地影响了原丝的热效应变化;纤维在180～340℃主要为脱水反应;原丝及经脱水剂、O_3和O_3综合脱水剂处理的纤维,其脱水反应的表观活化能分别为:164.3kJ/mol,92.9kJ/mol,130.5kJ/mol和117.6kJ/mol。     

钢纤维聚合物混凝土抗压本构关系

钢纤维聚合物混凝土是由聚合物混凝土基体和钢纤维共同组成的纤维增强复合材料，它的力学行为不仅依赖于聚合物混凝土基体的行为，而且与钢纤维的掺量、分散特征以及钢纤维的几何尺寸有关，本文将基于损伤力学原理研究在不同纤维掺量下的钢纤维聚合物混凝土的全程压力-应变曲线及其本构模型。     

The application of microencapsulated phase‐change materials to nylon fabric using direct dual coating method

The fabrication of functional textiles able to provide thermal regulation and comfort for the body has attracted increasing interest in recent years. This research investigated fabric coatings containing energy absorbing, temperature stabilizing, phase‐change material microcapsules (PCMMcs), and their methods of application. Specifically, a coated fabric was directly prepared by a dual‐type coating method, in which the PCMMcs were dispersed in a polyurethane coating solution with no binder. The thermal performances of the dual‐coated samples were evaluated by differential scanning calorimetry, and their physical characteristics were examined by scanning electron microscopy, thermal vision camera, porosity, water vapor transmission rate (WVTR), and water entry pressure (WEP) analyses. Furthermore, the microclimate characteristics of the thermally enhanced fabrics were investigated under experimental conditions using a human‐clothing‐environment (HCE) simulator system. The study results confirmed the superior performance of the dual‐coated fabrics in terms of thermal regulation and body comfort, compared with those coated by the dry or wet coating method, because of the improved WEP, WVTR, and thermal performance. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effect of high temperature alkali cooking on the constituents,structure and thermal degradation of hemp fiber

Degumming of hemp fiber by high temperature alkali cooking was investigated, and the effect of temperature and dosage of alkali on the constituents, structure, and thermal degradation of hemp fiber was also discussed in this work. The morphology, structure, and thermal degradation of hemp fiber after high temperature cooking were investigated through SEM, FTIR, WAXD, and TG analysis. The results indicated that the high temperature cooking process was effective for removing hemicelluloses and lignin and could also improve the thermal stability of cellulose. Crystallinity index of the treated hemp fiber was increased, which was related to the cooking temperature and NaOH dosage. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008