常减压蒸馏装置换热网络的节能优化

利用夹点技术理论对耗能严重的某炼油厂常减压蒸馏装置进行用能诊断分析;并结合热力学原理得到两种优化换热网络,节能效果显著。     

油管电热清防蜡技术在强水敏油田的应用

江苏油田的庄 2、韦 2油田属强水敏油田 ,采用热 (水 )洗油井和化学清防蜡效果较差 ,两油田每年因洗井造成地层污染影响的产量损失在 5 0 0 0t以上 ,约占油田产量的 4 5 %。根据集肤效应 ,采用油管电热清蜡技术 ,在含水小于 6 0 %、井斜小于 4 0°的油井上可正常使用 ,一般通电加热 4 0～ 80min后 ,油井井口温度能达到 5 0℃左右 ,最高可达到 6 5℃以上 ,连续加热 5～ 6h即可达到清蜡目的 ,电热清蜡为周期 6 0～ 90d。影响电热清蜡主要指标因素是油井的产液量 ,产液量越小 ,所需要的加热电流和加热电压也越小 ,井口温度达到最高值越低 ,清蜡效果越差。试验的 7口井平均年度投入产出比达到 1∶5 ,经济效益和社会效益十分明显。     

反拍卖采购:一种新的采购模式

反拍卖采购技术以其新的理念和对信息技术的融合，能够使企业采购成本大幅度降低。通过对我国传统采购模式与反拍卖采购模式的对比分析，可以了解到反拍卖采购技术的应用前景。     

难处理金矿石加石灰焙烧焙砂中CaS的消除

介绍了用空气氧化预浸加石灰焙烧焙砂中的CaS，以消除其对金氰化的影响。预浸后金的氰化浸出率可从58％提高到80％以上。     

CIMSCLASS─—面向CIM的零件分类软件开发工具

介绍了一个能为工厂设置零件编码系统和开发零件分类系统的工具系统。该系统能适应用户的具体环境，能对零件的特征信息做较详细的描述和建立相应目标的零件分类系统，从而能在ＧＴ（成组技术）基础上为机械加工零件开发ＣＡＤ／ＣＡＰＰ／ＣＡＭ集成系统提供支持，以满足ＣＩＭＳ的需要。     

烯烃均相茂金属催化技术的工艺条件

烯烃均相茂金属催化技术的工艺条件潘智达孙俊全杨士林（浙江大学高分子科学与工程系，杭州３１００２７）ＰａｎＺｈｉｄａ，ＳｕｎＪｕｎｑｕａｎａｎｄＹａｎｇＳｈｉｌｉｎ（ＤｅｐａｒｔｍｅｎｔｏｆＰｏｌｙｍｅｒＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｅｒｉｎｇ，Ｚｈ...     

浅谈托辊的开发与实践

本钢１７００连轧机应用的托辊原由外企业制作，为了减少公司资金外流，公司技术人员和工人结合现有的生产条件，先后攻克了辊身铸造和加工，托辊装配等工艺方面的难关，研制成功了合格的产品，年创经济效益８０万元。     

Catalytic oxidation of sulfide ions over nickel hydroxides

The catalytic sulfide ion oxidation by oxygen to elemental sulfur over β-Ni(OH)₂ and LiNiO₂ has been studied. As a result of experimental investigation performed, a reaction mechanism is suggested which involves heterogeneous and homogeneous processes. Dioxygen activation in the heterogeneous process proceeds via a redox Ni²⁺ ↔ Ni³⁺ transition and participation of OH⁻ groups. The active HO⁻₂ species thus formed carries on the reaction in homogeneous phase. Nickel hydroxides are promising catalysts for practical application.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

现代汽车活塞制造技术总论

本文针对现代汽车活塞的生产技术特点,综述了制造技术及其装备的主要课题,重点分析介绍非圆裙面加工、异型销孔精镗、工艺基准的关键作用,变形对加工精度的影响,检测技术配套及全面提高铸件质量等关键问题的国内外发展动向。