Effects of Light, Oxygen, and pH on the Absorbance of 2,2-Diphenyl-1-picrylhydrazyl

ABSTRACT: The absorbance of 2,2-diphenyl-1-picrylhydrazyl (DPPH) at 517 nm in methanol and acetone decreased by 20 and 35% for 120 min at 25 °C under light, respectively; in the dark it did not change significantly for 150 min. Decomposition of DPPH under 21% oxygen after 90 min under light was significantly higher than that under 1% oxygen. Absorbance of DPPH in pH 4 buffer solution in methanol, and in pH 10 buffer solution in acetone, decreased by 55 and 80%, respectively, under light for 120 min. The evaluation of antioxidant activity by the changes of DPPH absorbance should be carefully interpreted since the absorbance of DPPH at 517 nm is decreased by light, oxygen, pH, and type of solvent in addition to the antioxidant.     

变频调速技术在济钢焦化厂高压氨水泵上的应用

济钢焦化厂高压氨水泵变频调速系统采用变频器和PLC相结合的方式 ,具有调速精度高、节能等多种功能 ,保证氨水泵正常工作。全年可增加经济效益 77.3万元。     

FLOW OF NEWTONIAN FLUIDS THROUGH SINUSOID ALLY CONSTRICTED TUBES. NUMERICAL AND EXPERIMENTAL RESULTS

Numerical and experimental predictions of pressure drops in the flow of Newtonian fluids through sinusoidally constricted tubes (SCT) are carried out. The numerical evaluations analyzed in this work are obtained from the following methods: Geometric Iteration (GJM), Geometric Iteration with First and Second Upwinds (GIM1, GIM2), Successive Over Relaxation by Line (SORBLM), Global Galerkin Spectral Method (GGSM), Collocation (CM) and Dufort-Frankel (DFM). The GIM1, GIM2 and SORBLM are applied to SCT and explained in this work. The other methods have been previously reported in the literature with the same purpose. Experiments are accomplished for constrictions of approximately 40,60 and 80% of the average tube diameter and results compare well with numerical predictions of the steady flow. It is concluded that special attention should be given to evaluations of the friction factor ƒ for Reynolds numbers Re between the onsets of flow separation and turbulence due to flow instability. Finally, the SCT as a model for porous media (PM) is discussed.     

A new bubble-point-pressure correlation for the binary LiBr/H2O solution

In accord with the increasing concern about the global environmental issues, the absorption refrigeration heat-pump systems are currently being considered very promising and attractive. For the purpose of supporting the advanced R&D technology in this area, we have developed a novel correlation to represent the bubble-point pressures of LiBr H₂O solutions. The developed correlation covers the most extensive range of validity ever proposed: 273–483 K for temperatures, 0.05 kPa to 1.0 MPa for pressures. and 29 76 wt% LiBr for concentrations.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994. Boulder, Colorado, U.S.A.     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.     

焚烧炉控制系统

化工废气、废液焚烧炉是一种常用的环保处理装置，就其工艺详细介绍焚烧炉燃烧过程的控制及其安全联锁措施。     

论高层建筑中央空调水系统水压试验的步骤

通过对中央空调水系统安装的特点分析,确定了应用效果良好的试压步骤。     

柴油机针阀体的乙炔低压渗碳

乙炔低压渗碳可以有效地避免在真空渗碳过程中产生炭黑和焦油，同时由于乙炔具有较高的供碳能力，使这一技术尤其适用于针阀体这样的小直径深盲孔零件。     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

井下储存式电子压力计的软件设计

周静等．井下储存式电子压力计的软件设计．测井技术，１９９４，１８（４）：２８１～２８７论述小功耗井下储存式电子压力计测试系统的组成及系统软件工作原理。利用软硬件结合的方式，来达到降低功耗之目的。特别是采用了软件监视定时器，以便提高系统的稳定性。系统的特点是功耗小，抗干扰能力强，稳定性好，精度高。它与袖珍计算机ＰＣ－Ｅ５００配合进行采集，处理和绘出压力恢复曲线。