Effects of the electrospray ionization parameters on the formation and morphology of colloidal microspheres of polyacrylonitrile

Polyacrylonitrile colloidal microspheres have been successfully prepared with different concentrations of electrospraying polyacrylonitrile solutions. The morphology of the colloidal spheres has two kinds of structures and is strongly affected by electrospray‐ionization parameters, such as the polymer concentration, applied voltage, and distance between the electrodes. The solvent can also affect the morphology of polyacrylonitrile. The optimum conditions for preparing colloidal spheres have been found, and differential scanning calorimetry results indicate that polyacrylonitrile colloid spheres are amorphous. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2889–2893, 2006     

有机玻璃的增韧研究

研究了不同聚合方法制备的聚丙烯酸丁酯（PBA）对浇铸型有机玻璃（PMMA）的增韧改性，研究结果表明，当PBA以纳米粒子簇分散在PMMA基体中时，对PMMA有较好的增韧改性效果。当PMMA中无皂乳液聚合PBA（e-PBA)的质量分数为0.5%时。改性PMMA的冲击强度比基体提高38%。SEM观察表明，本体聚合PBA（b-PBA)橡胶粒子以独特的纳米簇状结构均匀分布在PMMA基体中，大量的微裂纹以b-PBA粒子为中心呈放射状向外辐射，这些微裂纹在试样破坏的过程中吸收了大量的冲击能，使改性PMMA韧性得以提高。     

Differently sized native milk fat globules separated by microfiltration: fatty acid composition of the milk fat globule membrane and triglyceride core

The aim of this study was to characterize the fatty acid composition of the core and membrane of differently sized milk fat globules separated by microfiltration, which can now be used to manufacture dairy products. Native milk fat globules of various mean diameters, ranging from d₄₃ = 2.3 µm to 8.0 µm, were obtained using microfiltration of raw whole milk. After milk fat globule washing, the milk fat globule membrane (MFGM) and the triglyceride core (TC) were separated by manual churning. After total lipid extraction from each fraction, their fatty acid composition was characterized using methyl ester analysis by gas chromatography. Regardless of season, no significant differences were observed in the fatty acid composition of the MFGM phospholipids. Conversely, significant differences were found in the fatty acid composition of TC; particularly, small fat globule TC contained more medium‐chain fatty acids and less stearic acid than large fat globule TC. These results show that the previously observed differences in total fatty acid composition among differently sized milk fat globules are due to their triglyceride composition and MFGM amount rather than to the composition of the MFGM.     

非饱和黏性土直剪强度特性及其修正分析

为研究非饱和黏性土的直剪强度特性,采用非膨胀土及两种不同干密度的弱膨胀土进行了包含低应力状态下8种不同上覆压力的直剪试验。试验结果表明,随着上覆压力的增大,最大剪应力及所对应的剪切位移逐渐增大,试验中低应力状态下测定的土体凝聚力小于高应力状态,且试验中的上覆压力对膨胀性土凝聚力的影响大于非膨胀性黏土;而低应力状态下测定的土体内摩擦角大于高应力状态。对直剪试验中上下盒接触面积减小对抗剪强度参数测定的影响进行了分析,分析表明,接触面积减小对抗剪指标有影响,但极其微小。提出对膨胀土边坡浅层破坏进行稳定性分析时应采用低应力下的抗剪强度参数。     

Zn-Al-CO_3水滑石晶粒尺寸控制与光屏蔽作用研究

在旋转液膜反应器中制备成核浆液 ,通过控制晶化温度制备了不同粒径且晶体结构完整的Zn Al CO3水滑石 (LDHs)。将不同粒径的Zn Al CO3LDHs配成质量分数为 0 0 2 %的水分散液 ,测定在紫外 -可见光范围的透过率 ,结果发现 ,随晶化温度的升高 ,LDHs粒径增大 ,样品对紫外及可见光的阻隔作用增强 ;Zn Al CO3LDHs在不同波长下的吸光度与晶体粒子在a轴和c轴方向的尺寸呈线性关系。由外推法求得了Zn Al CO3LDHs对各波长紫外 -可见光产生屏蔽作用的晶粒尺寸阈值。对波长分别为 2 90、3 2 0、40 0、60 0和 80 0nm光波能够产生屏蔽作用的Zn Al CO3LDHs ,其粒子尺寸在a轴方向需分别大于 3 2 92、3 3 77、3 4 77、3 5 5 6、3 5 79nm ;在c轴方向需分别大于 9 73、12 79、16 47、19 3 5、2 0 2 2nm。     

超临界CO2GAS沉析HMX制细过程的影响因素

研究了超临界CO2GAS沉析丙酮溶液中HMX的过程压力、温度、溶液初始浓度和溶液的膨胀速度及影响晶体粒度的因素。结果表明，压力增加，沉析颗粒的平均粒度减小；温度控制沉析晶体的晶型，对颗粒度的影响相对较小，温度增加，沉析平均粒度略有增加；溶液初始浓度对平均粒度的影响相对较大，膨胀速度亦是影响粒度及其分布的一个因素。快速膨胀溶液．并使过饱和度足够大，使过饱和度主要消耗在成核上，可得到颗粒小、分布窄的HMX颗粒。     

采用不同锰源合成尖晶石LiMn2O4正极材料

The spinel LiMn2O4 cathode material was synthesized with the solid-state reaction method. Four manganese compounds including electrolytic manganese dioxide (EMD), MnCO3, Mn3O4 and nano-EMD were used as Mn sources while LiOH·H2O was used as the uniform Li source. The crystal structure characteristics of these samples produced were investigated by means of XRD, SEM, particle size distribution analysis and specific surface area testing. Their electrochemical properties were also studied by comparing their specific capacity, charge and discharge efficiency and cycle performance.     

核壳结构聚合物乳液乳胶粒粒径及重量分布测试

对核壳结构聚合物乳液乳胶粒的粒径及其分布进行了测试,并与同一聚合物体系的其它乳液加以比较、分析,得出其粒径最小、分布最均匀的重要结论.     

基于DEM的碎屑流运动特性数值模拟

采用颗粒离散元法建立了碎屑流三维数值模型,分别从整体和局部对碎屑流运动特性进行深入分析。结果表明:碎屑流的运动过程可分为启动加速、高速滑动和减速堆积3个阶段;边坡底面平整时,堆积体中大颗粒堆积在表面,而细小颗粒位于中下部位;碎屑流运动速度和能量损失受颗粒间的接触碰撞影响大;碎屑流不同部位运动速度最大值相同,达到速度峰值的时间与颗粒的初始水平位置有关,与深度无关;堆积体分区明显,堆积体中的颗粒按初始水平位置依次排布;坡脚位置堆积深度最大,往两侧逐渐减小;碎屑流在运动初期和末期横向运动明显,扩大了灾害影响范围。     

超细粒子催化剂的研究进展及其应用

介绍了超细粒子催化剂的性质及现有的一些制备方法，并对制备方法的优缺点进行了评价。着重探讨了溶胶-凝胶技术所具备的特点及一些内在缺点，并展望了超细粒子催化剂的应用前景。