Second-law-based thermodynamic analysis of two-stage and mechanical-subcooling refrigeration cycles

Thermodynamic analysis of HFC-134a vapor-compression refrigeration cycles is investigated by both the first and second laws of thermodynamics. Second-law analysis is carried out for both two-stage and mechanical-subcooling refrigeration cycles. The analysis is performed on each of the system components to determine their individual contribution to the overall system irreversible losses. It is found that most of the losses are due to a low compressor efficiency. Irreversibilities of expansion valves and condenser are also significant. In addition, it is shown that the optimum inter-stage pressure for two-stage and mechanical-subcooling refrigeration systems is very close to the saturation pressure corresponding to the arithmetic mean of the refrigerant condensation and evaporation temperatures. These results are compared with the existing practice in the industry. Furthermore, theoretical results of a two-stage refrigeration system performance are also compared with experimental values for a CFC-22 system.     

Impact of uncertainties on estimations of heat pump cycle performance

Sensitivity analysis is used to show how uncertainties in basic factors, such as heat transfer, pressure drop, compressor efficiency, and thermophysical properties, influence the result of heat pump cycle performance estimations. By comparing the results of this analysis with uncertainty levels of estimations and experimental determinations, it is established to what extent improvements in accuracy are needed. The investigation was carried out for several different applications and, as working fluids, both pure substances and non-azeotropic mixtures were examined. It was found that evaporation heat transfer and compressor efficiency are two areas where improvements are needed. It is also shown that estimates using very accurate, substance-specific, equations of state differ from those using more general types by up to 1 % for COP and 2% for capacity.     

搅拌工艺对半固态Y112铝合金组织及性能的影响

采用自行研制的机械搅拌装置,研究了不同工艺参数对半固态Y112铝合金组织及性能的影响.研究表明,搅拌温度越高,搅拌速度越大,固相颗粒越细小、均匀和圆整,其抗拉强度与伸长率越高;但温度太高,固相颗粒会熔化,抗拉强度及伸长率也降低;随搅拌时间的延长,固相颗粒先变得细小、均匀和圆整,然后长大,抗拉强度、伸长率先升高后降低.     

Numerical study on PEMFC’s geometrical parameters under different humidifying conditions

Steady-state and three-dimensional simulations were carried out to study the influences of geometrical parameters on the performance of PEMFC under different hydrating conditions. Flow fields, species transport, transport of water in polymer membrane and movement of liquid water in cathode and anode porous layers were determined, in order to accomplish a complete estimation of ohmic and concentration losses of PEMFC power. The geometrical parameters were thickness of the polymer membrane, cathode catalyst layer as well as gas channel to rib width ratio. Every simulation was made under different relative humidities of inlet flows (50 and 100%) for every change of characteristic length. Results show that the influence of the geometrical parameters on ohmic and concentration losses is of considerable importance. The performance of PEMFC is seriously affected under dehydrating conditions. However, such performance may be considerably improved by using suitable geometrical parameters. Cathode and anode liquid saturation may not only affect the transport of species, but also the polymer electrolyte water content. These results show the importance of simultaneously calculating both the water absorption and desorption through the polymer electrolyte and the liquid saturation in the cathode and anode porous mediums to obtain an actual view of ohmic and concentration losses of the PEMFC performance.     

Optimization of downhole pump setting depths in liquid-dominated geothermal systems: A case study on the Balcova-Narlidere field,Turkey

Downhole pumps are being used increasingly more often in low-enthalpy geothermal wells. The depth at which these pumps are installed depends on the physical and chemical characteristics of the geothermal fluid, the production flow rate, and the reservoir pressure and permeability. In this study we have investigated the factors affecting pump setting depths in low-temperature, liquid-dominated geothermal systems and defined the relationship between flow rate and pressure drawdown based on multi-rate test results. The methodology proposed was applied to the Balcova-Narlidere geothermal field, Turkey. It was found that the most important parameters for determining the capacity and setting depth of a downhole pump were flow performance, non-condensable gas concentration, and temperature. The implementation of the methodology is illustrated.     

单小区模型的掉话率分析

掉话率是无线通信网络中最重要的关键性能指标(KPI)之一,本文分析了中国移动在讨论网络性能评估方法时提出的3个不同的掉话率计算公式,通过建立一个单小区的模型,使用一些合理的假设和分析,从理论上确定了一个最为准确的计算公式.     

有机盐聚合醇氯化钾钻井液的应用

霍尔果斯背斜构造极其复杂,内应力极高,地层倾角大,断层、破碎带多,并存在高低压互层;安集海河组的灰绿色软泥岩水化严重并具有粘弹塑性.该区块重点探井霍003井三开、四开井段选用有机盐聚合醇氯化钾钻井液,同时为保证钻井液在高密度下（2.55 g/cm^3）具有好的流变性,使用活化铁矿粉、活化重晶石加重.应用结果表明,由于采用了强抑制和多元封堵的措施,该钻井液具有良好的流变性和较强的携带能力,钻进中曾携带出重2.8 kg和5.1kg的大掉块;滤失量低,泥饼质量好,封堵能力强,造壁能力强,减轻了井下阻卡程度;有良好的储层保护能力;在室内研究的基础上,经过现场合理使用和维护钻井液,霍003井提高了机械钻速,缩短了钻井周期,井身质量优于邻井.指出在高密度下,未选出适合有机盐聚合醇氯化钾钻井液的稀释剂,钻井液流动性较差.     

The appropriateness of the systematic framework to develop diagnosis procedures of nuclear power plants—an experimental verification

It has been well recognized that a diagnosis procedure that allows operators to successfully identify the nature of an on-going event is inevitable for an effective and appropriate recovery. Unfortunately, studies for a framework that can suggest a unified and consistent process in constructing a serviceable diagnosis procedure seem to be scant. Thus, Park et al. have suggested a systematic framework that can be used to construct a useful diagnosis procedure. In addition, the diagnosis procedure that is currently in use at the reference nuclear power plant (NPP) is reformed in order to demonstrate the appropriateness of the suggested framework. However, the necessity of a well-designed experiment is proposed to confirm the appropriateness of the suggested framework.In this regard, in this study, an experiment is conducted using a full-scope simulator of the reference NPP. From the experiment, two sets of operators' diagnosis performance data are collected, and then they are compared to investigate the change of an operator's diagnosis performance with respect to two types of diagnosis procedures.As a result, it is shown that an operator's diagnosis performance is improved when the revised diagnosis procedure is used. Therefore, it is reasonable to conclude that the suggested framework is useful in constructing an effective diagnosis procedure.     

LASER ENHANCED ELECTROCHEMICAL MACHINING PROCESS

An experimental apparatus was designed and built for the hybrid process of laser enhanced electrochemical machining (ECM). Comparison experiments had been done between solely ECM and laser enhanced ECM. The machining performance of hybrid process was investigated and compared with solely ECM. The principle of the hybrid process was exposed by analyzing the microstructure of machining surface. The results show that the hybrid process has advantages in machining accuracy, surface quality, and machining efficiency.     

X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.