管壳式换热器流场三维数值模拟

采用多孔介质方法 ,在PHOENICS 3 3程序的基础上建立了换热器的三维流动计算模型。引入体积穿透率、表面穿透率、分布阻力等来描述换热器内的管束。模型通过计算Halle等[1] 的实验工况来进行验证 ,并尝试用于计算 2 0 0MW低温供热堆主换热器内的流场     

Preparation of Ultra—fine Aluminum Nitride in Thermal Plasma

Ultra-fine aluminum nitride has been synthesized by the evaporation of aluminum powder at atmospheric-pressure nitrogen plasma in a hot-wall reactor.The average size of aluminum nitride particle is 0.11μm measured by scanning electric mirror(SEM),and the purity is at least over90% evaluated by X-Ray diffraction(XRD).The conversion of Al powder to aluminum nitride is strongly depended on the injection of NH3.Typical experimental parameters such as the feed rate of raw material,the flow rate of ammonia and the position of injecting aluminum powder into the reactor are given.     

Ideal-gas thermodynamic properties for natural-gas applications

Calculating caloric properties from a thermal equation of state requires information such as isobaric heat capacities in the ideal-gas state as a function of temperature. In this work, values for the parameters of thec _p ⁰ correlation proposed by Aly and Lee were newly determined for 21 pure gases which are compounds of natural gas mixtures. The values of the parameters were adjusted to selectedc _p ⁰ data calculated from spectroscopic data for temperatures ranging from 10 to 1000 K. The data sources used are discussed and compared with literature data deduced from theoretic models and caloric measurements. The parameters presented will be applied in a current GERG project for evaluating equations of state (e.g., the AGA 8 equation) for their suitability for calculating caloric properties.     

多种采暖方式的特点及其选择

介绍了多种采暖方式．并对各种采暖的适用性、一次性投资、运行费用和对环境的影响作了对比，提出了选择的优先顺序，为房地产开发商和用户对于采暖方式的选择提供了参考。     

铸造Ti—0.2Pd合金SF—1000双级风机叶轮的研制

Ｔｉ－０．２Ｐｄ合金ＳＦ－１０００双级风机叶轮是大型盐酸再生设备的主要部件，采用整体铸造方法制造，无论在技术上还是经济上都是十分有利的。本文主要介绍采用加工石墨，铸铁组合型，真空电弧凝壳熔炼铸造工艺，成功地研制出整体铸造风机叶轮。     

Finite Element Analysis of a Moving Boundary Value Problem

A finite element formulation and the solution of a set of nonlinear coupled heat and mass transfer equations for a two-phase system with a moving evaporation interface is presented. The interface condition takes into account the moisture transfer balance at the moving boundary. The finite element results were compared with existing results for a single phase system for model validation. In the two-phase system, the movement of evaporation front has an appreciable effect on the temperature and moisture distribution inside the porous medium during drying. The effect of the nondimensional heat of vapourization parameter γ on the evaporation front, temperature and moisture distribution in porous medium was studied. The higher the value of γ, the slower is the movement of the evaporation front. The temperature decreased and the moisture content increased as the nondimensional vapourization parameter γ increased. This model has potential applications in studying the heat and mass transfer characteristics in food and biomaterials.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

Ni对球墨铸铁热处理的影响

采用电子探针，图象分析仪、差质变分析仪和Ｘ射线衍仪定量研究了Ｎｉ在球铁中的分布和Ｎｉ铸态球铁组成相比例奥氏体中含碳量以及贝氏体转变ＴＴＴ曲线线的影响，结果表明，Ｎｉ在球铁中呈连续负偏析，其加入可以影响球铁组成上比例，并使粤氏体中含碳量和贝氏体转变孕育期期增加。     

Prediction of evaporation heat transfer coefficient and pressure drop of refrigerant mixtures

A study on the prediction of heat transfer coefficient (HTC) and pressure drop of refrigerant mixtures is reported. HTCs and pressure drops of prospective mixtures to replace R12 and R22 are predicted on the same cooling capacity basis. Results indicate that nucleate boiling is suppressed at qualities greater than 20.0% for all mixtures and evaporation becomes the main heat transfer mechanism. For the same capacity, some mixtures containing R32 and R152a show 8.0–10.0% increase in HTCs. Some mixtures with large volatility difference exhibit as much as 55.0% reduction compared with R12 and R22, caused by mass transfer resistance and property degradation due to mixing (32.0%) and reduced mass flow rates (23.0%). Other mixtures with moderate volatility difference exhibit 20.0–30.0% degradation due mainly to reduced mass flow rates. The overall impact of heat transfer degradation, however, is insignificant if major heat transfer resistance exists in the heat transfer fluid side (air system). If the resistance in the heat transfer fluid side is of the same order of magnitude as that on the refrigerant side (water system), considerable reduction in overall HTC of up to 20% is expected. A study of the effect of uncertainties in transport properties on heat transfer shows that transport properties of liquid affect heat transfer more than other properties. Uncertainty of 10.0% in transport properties causes a change of less than 6% in heat transfer prediction.     

The effect of temperature on the dynamic characteristics of heat-resistant thermoplastic composites

Two thermoplastic and two thermosetting fibrereinforced plastic composites were subjected to dynamic tests over a wide range of temperature, covering both cryogenic and hot environments. The thermal behaviour of each composite, as indicated by its dynamic mechanical properties, was assessed individually, and was compared collectively with that of the other composites.