Plasma Sprayed Hydroxyapatite Coatings with Nano-hydroxyapatite Prepared by Ultrasonic Precipitation Process

Nano-particle hydroxyapatite （ HA ） was prepared with a novel ultrasonic precipitation process and the as-prepared nanopowder was used to produce hydroxyapatite （ HA ） coatings on titanium substrate via plasma spraying. The phase and the microstructare of the coating were characterized by X- ray diffraction （XRD） and scanning electron microscopy （SEM）. Results showed that spherical particles could be prepared by ultrasonic precipitation process; and a corresponding dense HA coating with molten surface and low-porosity cross-section structure was acquired. During the plasma spraying process, new phases of Ca3 （ PO4 ）2 and Ca2 P2O7 were generated. After heat-treating at 800℃ for 1 h, the contents of Ca3 （ PO4 ）2 and Ca2 P2O7 decreased while HA content increased. Tensile adhesion tests showed that the plasma sprayed coating prepared with the spherical nanoparticles exhibited high tensile bond strength.     

微滤膜清洗的研究

用次氯酸钠溶液、氢氧化钠溶液和盐酸溶液对小型微滤膜进行化学清洗试验,比较试验结果认为,用次氯酸钠溶液对受污染的微滤膜清洗更为有效,从而为鄂尔多斯羊绒集团污水处理厂中的大型连续微滤化学清洗提供依据.     

Inductively coupled plasma etching of InGaP, AllnP, and AlGaP in Cl2 and BCl3 chemistries

Dry etching of InGaP, AlInP, and AlGaP in inductively coupled plasmas (ICP) is reported as a function of plasma chemistry (BCl₃ or Cl₂, with additives of Ar, N₂, or H₂), source power, radio frequency chuck power, and pressure. Smooth anisotropic pattern transfer at peak etch rates of 1000–2000Å·min^?1 is obtained at low DC self-biases (?100V dc) and pressures (2 mTorr). The etch mechanism is characterized by a trade-off between supplying sufficient active chloride species to the surface to produce a strong chemical enhancement of the etch rate, and the efficient removal of the chlorinated etch products before a thick selvedge layer is formed. Cl₂ produces smooth surfaces over a wider range of conditions than does BCl₃.     

AHMED experiments on hygroscopic and inert aerosol behaviour in LWR containment conditions: experimental results

Hygroscopic NaOH, CsI, CsOH and inert Ag aerosol behaviour at different temperatures and relative humidities (RH) has been studied in a well instrumented and controlled vessel of 1.81 m³ total free volume. Homogeneous thermal-hydraulic conditions for aerosol measurement in the vessel were achieved. The aerosol number and mass concentration were measured continuously during the experiments using a Condensation Nucleus Counter and a Tapered Element Oscillating Microbalance. The particle size distribution and chemical composition in the test conditions were measured by Berner low pressure impactors. In the case of NaOH the half life of the aerosol mass concentration was more than four times longer at low RH (22%) as compared to high RH (96%). The half lives of the CsOH and CsI aerosols were only twice as long at low RH as compared to high RH. Thus at high RH (96–97%) the half lives of CsOH and CsI were twice as long as the half life for the NaOH aerosol. The faster decay of the NaOH aerosol is due to the smaller density decrease of NaOH during water condensation. CsOH particles grew rapidly to their equilibrium size at all humidities. The measured equilibrium size for CsOH aerosol agree well with the calculated particle size at different RHs. Experimental results were also compared with calculations obtained by severe accident computer codes. These calculated results will be presented in a later paper.     

太钢4号高炉喷煤站应用MFD—Ⅲ型布袋除尘器的实践

太钢４号高炉喷煤站从１９９０年起采用ＭＦＤ－Ⅲ型脉动反吹式布袋除尘器。这种除尘器采用脉动式反吹清灰设施，合理布置布袋间距，布袋支撑骨架及选用针呢材质的布袋，过滤面积大，反吹清灰效果好，设备运行平稳，除尘效率高达９９．８％，排放浓度小于１０ｍｇ／ｍ＾３，故障率低。     

高功率激光焊接光致等离子体的检测

系统地归纳了高功率激光焊接过程中光致等离子体的声、光、电、热等四种特征信号，综述了国外在等离子体信号检测方面的试验方法及研究进展，分析了未来的发展趋势     

Estimation of fouling in a plate heat exchanger through the application of neural networks

Pasteurization is an important, if not the most important, process step in the packaging of milk. It is subject to alterations stemming from the variation in the temperature, pH and raw milk quality. The variability may manifest itself in changes in the formation of the deposit (fouling) in the pasteurization unit, such that there is a need for tools, both instrumentation and computational, to help in monitoring the process and keeping it on the desired course. In this paper we describe a practical procedure based on artificial neural networks (ANN) that allows prediction of the deposit thickness, the overall heat transfer coefficient and the critical time (the time that the unit has to be stopped for cleaning) for reducing the impact of fouling on such processes. The procedure determines when the cleaning operation is required once the system is under critical conditions of operations. A combination of fundamental studies and plant measurements were used for study of the operating conditions and thus evaluation of the trades‐offs between operating conditions and longer operating life span. The results are encouraging, enough to validate current operating industrial techniques. Copyright © 2005 Society of Chemical Industry     

Plasma Discharge Initiation of Explosives in Rock Blasting Application： A Case Study

A plasma discharge initiation system for the explosive volumetric combustion charge was designed, investigated and developed for practical application. Laboratory scale experiments were carried out before conducting the large scale field tests. The resultant explosions gave rise to less noise, insignificant seismic vibrations and good specific explosive consumption for rock blasting. Importantly, the technique was found to be safe and environmentally friendly.     

ICAP-AES等离子体发射光谱法测定氧化铁粉的杂质元素

介绍了ICP等离子体光谱仪的原理及测定高纯氧化铁中铝、钙、硫、钾、镁、锰、钠和钛等8种杂质元素的分析方法，考察了样品的溶解方案及工作曲线的选择，确定了仪器最佳工作条件和方法检出限。     

Microwave plasma synthesis of TiN and ZrN nanopowders

This work demonstrates that TiN and ZrN nanopowders can be prepared by microwave plasma synthesis method. The effects of flow rate of plasma forming gas, flow rate of carrier gas and feeding rate of precursor raw material to the average particle size were studied. The TiN and ZrN nanopowders were characterized by means of transmission electron microscopy (TEM) and X-ray diffraction (XRD).