高阻值Cd1-xZnxTe晶体的生长及其性能测试

通过适当的工艺措施，采用Bridgman法生长了直径为30mm的X射线及γ射线探测器级的Cd.9Zn0．1Te晶锭．测试结果表明：该晶锭结晶质量良好，位错密度低，成分均匀，杂质含量低，红外透过率和电阻率都十分接近本征Cd.9Zn0．1Te的值．并从晶体的生长特性、缺陷和杂质的角度，分析了生长高性能晶体的条件，研究了生长Cdl-xZnxTe晶体的x值与缺陷和杂质浓度之间的关系．     

超高纯铜的制备方法和应用

简要介绍了超高纯铜(UHPC)的几种精炼方法，以及它在工业方面的应用。并对超高纯铜的研究开发趋势及应用前景进行了展望。     

Pure perceptual-based sequence learning.

Learning a sequence of target locations when the sequence is uncorrelated with a sequence of responses and target location is not the response dimension (pure perceptual-based sequence learning) was examined. Using probabilistic sequences of target locations, the author shows that such learning can be implicit, is unaffected by distance between target locations, and is mostly limited to first-order transition probabilities. Moreover, the mechanism underlying learning affords processing of information at anticipated target locations and appears to be attention based. Implications for hypotheses of implicit sequence learning are discussed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

气相色谱在线分析变压吸附法制纯氢中的总碳

利用带镍加氢转化炉的气相色谱仪 ,在线分析变压吸附法制纯氢中的总碳。该法用变压吸附法制的纯氢作燃气 ,在检测器前端将氢气中的CO和CO2 转化为CH4,然后用氢火焰离子化检测器检测 ,直接以检测器的信号 (mV)进行定量。当氢气中总碳体积分数在 1 9～ 5 0 0 μl/L时 ,FID信号值与总碳体积分数有良好的线性关系。方法回收率为 99 90 %～ 10 1 9%,相对标准偏差 <1%。     

纯铜双层辉光离子渗钛组织形成机理及性能分析

采用双层辉光离子渗金属技术对纯铜进行了渗钛处理。用配有能谱仪(EDS)的扫描电子显微镜(SEM)、X射线衍射仪和透射电子显微镜对合金层的显微组织形貌、钛含量分布、相组成及相结构类型进行了观察与测定，对合金层的形成机理进行了探讨，并对其性能进行了对比测定。结果表明：渗钛层由合金层和扩散层组成，合金层主要由TiCu (Cu)固溶体 TiCu4构成，TiCu4为Dla型有序相，TiCu为B2型有序相，扩散层为(Cu)固溶体。渗钛处理后纯铜的表面得到显著强化。     

超纯汞生产新工艺的技术研究

本文着重介绍了超纯汞生产新工艺的基本原理的理论探讨及生产工艺过程的控制。     

A prediction method for thermal conductivity of alternative refrigerants in the liquid phase

A prediction method for the thermal conductivity of halocarbon refrigerants in the saturated liquid state in the reduced temperature range 0.3 to well above 0.9 is presented in this paper. The aim of the method is to present a very simple calculation of the transport property useful for engineering purposes. The method determines thermal conductivity as a sole function of the reduced temperature and requires the knowledge of a parameter dependent upon easily available physical constants characteristic of each compound. The method is validated against experimental data available in the literature, giving average absolute deviations which are usually less than 5%, with maximum absolute deviations generally less than 10%. An extension of the method to estimate thermal conductivity of binary mixtures is also presented, along with a comparison with the few experimental data available in the literature.Paper presented at the Twelfth Symposium on Thermophysical Properties, June 19–24, 1994, Boulder, Colorado, U.S.A.     

A method for evaluating the mechanical performance of thin-walled titanium tubes

A method which was developed to compare the stress–strain properties of three types of thin-walled, commercially pure titanium tubes is presented. The tubes were of types intended for use in large heat-exchanger applications and were to be subjected to significant plastic deformation during subsequent assembly processes. It had been anticipated that small differences in chemical composition and tube-drawing treatment would produce quite different characteristics. It is known that the properties of titanium can exhibit considerable degrees of anisotropy, especially for wrought products; although axial properties of the materials could be evaluated using standard test equipment and procedures, a novel testing system had to be designed to allow the circumferential properties to be assessed. Significant differences between tube types were observed and anisotropic material behaviour was apparent.     

Vertical bridgman techniques to homogenize zinc composition of CdZnTe substrates

In order to improve the Zn homogeneity along the axial direction of CdZnTe boule, we have employed a modified Bridgman technique using a (Cd, Zn) alloy source in communication with the melt, whose temperature has been gradually changed from 800 to 840°C during growth. Electron probe microanalysis (EPMA) measurements of Zn composition in the boule shows an excellent homogeneity of Zn along the axis of the CdZnTe boule compared with results in a boule grown by using a fixed source temperature. We have performed a numerical simulation to obtain the approximate temperatures of additional heating and cooling needed to improve the radial Zn homogeneity. CdZnTe boule has been grown by seeded vertical Bridgman furnace with two zones of heater and cooler. Ultraviolet/visible spectroscopic measurements of Zn composition over the length of the boule indicate that the radial distribution of Zn composition is very homogeneous in the body region of the boule, where the radial variation of Zn composition is ±0.0005.