浸渗工艺对SiC/Al复合材料残余气孔率的影响

采用无压浸渗法制备了SiC/Al复合材料,从浸渗动力学和工艺方法的角度探讨了浸渗保温时间和降温方式对复合材料的残余气孔率的影响。结果表明:随着保温时间的适当延长,能有效地降低复合材料的残余气孔率;连续降温优于分段降温,有利于降低SiC/Al复合材料的残余气孔率。     

钢轨内残余应力的产生及其危害

从钢轨的生产工艺和使用情况人手，分析了钢轨内部残余应力的产生原因、分布状态。结果表明：钢轨在生产和使用过程中均可以产生残余应力；钢轨内部存在大且不合理的残余应力(轨头、轨底拉应力，轨腰压应力)，将会影响钢轨的使用和落锤性能，严重时会造成线路钢轨的突发性断裂或落锤试验不合格。     

碳氮共渗提高空心圆柱滚子轴承寿命的研究

通过GCr15钢碳氮共渗,在表层获得大量的残余奥氏体。磨损中,马氏体组织剥落,残余奥氏体则成小岛状,进而在表面迁移发生形变诱发马氏体相变,使耐磨性得以提高。同时,共渗在空心滚子内表面造成的压应力对改善弯曲疲劳性能有利。     

Optical Investigation of the Effects of Substrate Orientation on Oxidation of Single Crystal β-NiAl

The residual stresses in -Al₂O₃ scales formed on high-purity FeCrAl and FeCrAlY during oxidation at 1200°C and subsequent cooling and reheating were studied using photostimulated luminescence spectroscopy. Systematic measurements of the stress in the oxide were made as a function of both alloy thickness and cooling rate and the development of stresses in the oxide scale during thermal cycling was investigated as a function of the temperature. Depending on the ratio of the alloy and oxide-scale thicknesses, substantial stress relaxation was observed to occur during cooling at a rate of 8 K/min. Compressive growth stresses of 1 GPa were determined by comparing the residual-stress measurements at room temperature with those calculated based on thermal-expansion mismatch. No significant differences in the growth stresses, the total residual stresses, or the stress relaxation during thermal cycling were observed between the oxides formed on the Y-doped and undoped FeCrAl samples. Stress relaxation is also shown to lead to the development of tensile stresses in the oxide scale under certain conditions, in particular, those associated with slow cooling followed by rapid heating.     

40Cr钢电火花表面强化层的磨损特性研究

分析了在大接触应力的磨损条件下,表面残余应力和硬度对40Cr电火花强化层耐磨性的影响,探讨了其磨损机理。结果表明:滚动磨损和滚、滑动磨损时,随着试样表层硬度的提高,试样的耐磨性增大;强化层中的残余压应力可以提高强化层的硬度并增强其耐磨性。滚动磨损时,电火花强化层的磨损方式主要为粘着磨损、疲劳磨损和磨粒磨损三种机制;在滚、滑动磨损时,除上述三种机制外,还发生了氧化磨损。     

Effect of cold spray deposition of a titanium coating on fatigue behavior of a titanium alloy

The deposition of titanium on a titanium alloy substrate is being examined for potential use as a surface treatment for medical prostheses. A Ti6Al4V alloy was coated with pure titanium by cold gas dynamic spraying. Coatings were deposited onto samples with two different surface preparation methods (as-received and grit-blasted). The fatigue life of the as-received and grit-blasted materials, both before and after coating, was measured with a rotating-bend fatigue rig. A 15% reduction in fatigue endurance limit was observed after application of the coating to the as-received substrate, but no significant reduction was observed on its application to the grit-blasted substrate. The reduction in fatigue endurance limit has been related to the substrate-coating interface properties, the elastic modulus, and the residual stress states. This article was originally published inBuilding on 100 Years of Success, Proceedings of the 2006 International Thermal Spray Conference, (Seattle, WA), May 15–18, 2006, B.R. Marple, M.M. Hyland, Y.-Ch. Lau, R.S. Lima, and J. Voyer, Ed., ASM International, Materials Park, 2006.     

作保灵对长残效除草剂的解毒效应

利用田间试验方法研究保护剂长残效除草剂解毒效应。不同保护剂对豆磺隆解毒效应有差异，作保灵解毒效应最明显，但在除草剂高残留量时解毒作用下降。作保灵对三种长残效除草剂都具有明显的解毒作用，作物的出苗率可恢复80％～100％。解毒效应顺序为油莱＞白菜＞甜菜。     

氮化制度对Si-Al-Al2O3体系合成Sialon的影响

以SiC、α-Al2O3微粉、Si粉、Al粉为原料,在1450℃流动氮气中制备Sialon/SiC材料。研究了不同温度保温氮化对Sialon合成的影响。研究结果表明:有部分硅粉残余没有氮化;在1100℃保温氮化的氮化率高于在1150℃、1200℃保温氮化;1100℃保温氮化,残余Si量少、分布均匀,残余硅熔聚现象较轻,利于Sialon的合成。     

双通道喷嘴渣油气化过程(Ⅰ)冷模实验

基于对3套8.53MPa双通道喷嘴渣油气化装置普遍存在的工程现象的思考,组织了模型气化炉冷态试验。测试了3种模型在6种射流速度下的停留时间分布,7种模型在2种射流速度下的速度分布。给出了停留时间分布密度函数、无因次半速度半径轴向增长、径向射流最大速度轴向衰减和径向速度分布计算公式。     

氧化铝/莫来石复合陶瓷断裂行为研究

用X射线衍射方法测定了氧化铝/莫来石复合陶瓷的残余应力,并通过计算加以验证。在莫来石含量比较小的情况下,氧化铝/莫来石复合陶瓷基体拉应力与莫来石体积含量成线性关系。通过模型分析了氧化铝基体和莫来石颗粒的应力状态及其对裂纹扩展的影响。由莫来石颗粒引入的基体拉应力使裂纹倾向于向晶内扩展。观察了氧化铝/莫来石复合陶瓷断裂方式的转变,计算了穿晶断裂比率与基体应力的关系,进而建立了莫来石含量、基体应力、穿晶断裂比率三者的对应关系。这为复合陶瓷材料的制备和性能分析提供了可靠基础。