Effect of electrolysis superheat degree on anticorrosion performance of 5 Cu/（10NiO-NiFe2O4） cermet inert anode

5Cu/(10NiO-NiFe2O4) cermet inert anodes were prepared by cold-pressing and sintering process, and the effect of superheat degree of melting K3AlF6-Na3AlF6-AlF3 on their anticorrosion performance was studied under electrolysis conditions. The results show that, the fluctuation of cell becomes small with increasing of superheat degree, which is helpful to inhibit the formation of cathodic encrustation; the concentration of impurities from inert anode in bath goes up to certain degree, but it is far smaller than those in traditional high-temperature bath. Increasing the superheat degree of melting K3AlF6-Na3AlF6-AlF3 has unconspicuous effect on the contents of impurities in cathodic aluminum. The total mass fractions of Fe, Ni and Cu in aluminum are 15.38% and 15.09% respectively under superheat degree of 95 and 195 ℃. From micro-topography of anode used view, increasing the superheat degree can aggravate corrosion of metal Cu in inert anode, and has negative influence on electrical conductivity of electrode to some extent.     

Toward Largely Enhanced Toughness and Balanced Strength in PA1012/EPDM Blends via Synergistic Effect of Sacrificial Bonds and Network Structure

Here, zinc-neutralized ethylene propylene diene monomer (EPDM) ionomers with different neutralization levels are prepared through melt blending, and are then incorporated with polyamide 1012 (PA1012) to fabricate PA1012/EPDM ionomer blends. Interestingly, complex crosslinking networks are formed in the blends due to the construction of sacrificial bonds (Zn²⁺-carboxyl, Zn²⁺-amide). The as-formed network structure and sacrificial bond endow the PA/EPDM blends with largely enhanced toughness (16 times higher than that of neat PA), as well as balanced strength and stiffness. Meanwhile, the rheological behaviors of PA1012/EPDM ionomer blends indicate their relative low melting viscosity, which can avoid the processing shortcomings of plastics toughened with rubber. Moreover, PA1012/EPDM ionomer blends show obvious gelation behavior, and a maximum notched Izod impact strength exhibited at the gel point, in which unique double network structure can be observed obviously, indicating that there is a corresponding correlation between the rheological and mechanical parameters. Furthermore, the supper-toughening mechanism of PA1012/EPDM ionomer blends at gel point is explored, which origins from the large deformation and cavitation of rubber particles and the destruction of special double network morphologies. This study provides a novel and effective strategy to fabricate PA materials with outstanding toughness and excellent strength simultaneously.     

新能源汽车电池负极材料的制备与性能研究

采用原位合成法制备了镍-氧化镍/多孔碳纳米片（Ni-NiO/PCNs）负极材料,对比分析了氯化钠模板、退火温度和退火时间对负极材料物相组成、显微形貌和电化学性能的影响。结果表明,Ni/PCNs、Ni-NiO/C和Ni-NiO/PCNs负极材料都主要含有镍和无定型C相,且后2种负极材料还含有氧化镍相;300 ℃/4 h为Ni-NiO/PCNs负极材料适宜的退火工艺,此时Ni-NiO/PCNs负极材料中Ni-NiO粒子分散性较好且保持着三维片层结构,平均尺寸约为27 nm,Ni-NiO实现了对无定型C的包裹;退火时间过长（6 h）会使得镍粒子过氧化且发生团聚,而温度过高（400 ℃）会使得粒子以团聚为主,三维片层状结构消失。电流密度为1 A/g、循环5 000圈后Ni-NiO/PCNs负极材料的放电比容量为235 mA·h/g,此时的放电比容量约为首圈放电比容量的83.93%;Ni-NiO/C和Ni/PCNs负极材料在充放电循环过程中以及循环5 000圈后的放电比容量和容量保持率都明显低于Ni-NiO/PCNs负极材料,Ni-NiO/PCNs负极材料具有更好的循环稳定性,这主要与其具有独特的多孔三维片层结构有关。     

掺杂铁的二氧化铅电极的制备及性能研究

主要研究了不锈钢/PbO₂电极和掺杂的不锈钢/Fe-PbO₂电极的制备,用其对有机废水的处理效果及影响因素来评价该电极的性能。实验结果表明:采用恒流阳极电沉积技术制备的PbO₂电极,掺杂和不掺杂铁的电极主要成分都是β-PbO₂;两电极外观都没有明显的裂纹等缺陷,掺杂铁的二氧化铅镀层颗粒大小镶嵌,很好地清除了内应力,保证了基材与镀层不易脱落,未掺杂铁的二氧化铅镀层颗粒细小、均匀,内应力有些大;将Fe（NO₃）₂添加至电沉积溶液中,致使PbO₂电沉积层的析氧电位向正方向移动,改善了PbO₂电极的电催化活性,以至于更有利于氧化降解有机物。用改性的Fe-PbO₂电极和常规的PbO₂电极分别降解初始浓度相同的邻苯二酚和苯酚有机物废水,改性的Fe-PbO₂电极对苯酚和邻苯二酚的去除率均高于常规的PbO₂电极。掺杂铁的二氧化铅电极较未掺杂电极有更好的电催化活性,更高的析氧电位,更适宜于用作电催化阳极。     

银阳极泥氯化浸出回收金工艺研究

研究了银阳极泥氯化浸出回收金工艺。实验结果显示,在盐酸1.5 mol/L、硫酸0.75 mol/L、氯化钠35 g/L、氯酸钠与银阳极泥中金的质量比mNaClO     

Preparation and electrochemical performance of nanosized Co3O4 via hydrothermal method

The hydrotalcite-type cobalt compounds were prepared through oxidation of Co（OH）2 gel using NH4OH as precipitating agent and H2O2 as oxidant. These hydrotalcite-type cobalt compounds were transformed into Co3O4 through hydrothermal decomposition with nanostructural deformation. The precursor and product were characterized by Fourier-transform infrared（FT-IR） spectrum, X-ray diffractometry（XRD） and transmission electron microscopy（TEM）. The electrochemical performances of as-prepared nanosized Co3O4 as anode materials in lithium-ion batteries were tested by charge-discharge test in the voltage range of 0-3.0 V. The influence of morphology of Co3O4 particle on the capacity and cycling performance was studied. The results show that the shape and size of the final product can be controlled by altering cobalt sources. The irregular cubic Co3O4 with the average particle size of about 10 nm shows the best electrochemical performance. After 10 charge-discharge cycles, the specific charge capacity retains 555 mA.h/g.     

铜管内部阴极保护电位分布公式探讨

简述了管道内部阴极保护时电位分布公式的推导过程，重点推导和分析了双点阳极时其电位公式，并与文献中的同类公式进行了比较，同时，用该公式检验了试验结果。     

铝合金牺牲阳极电流效率损耗的微观分析

探针（EPMA）和能谱分析技术(EDAX)，考察了铝合金牺牲阳极的显微结构和腐蚀后的边缘形貌，讨论了电流效率和显微组织之间的关系.结果表明：晶界腐蚀引起的晶粒脱落是铝合金牺牲阳极电流效率损耗的重要原因.      

反应堆A0纯铝的点蚀模拟

测量A0纯铝在去离子水中的极化曲线用来模拟反应堆池壳的点蚀.研究表明A0纯铝在去离子水中很容易钝化.实验中用美国EG&G普林斯顿应用研究公司生产的273型恒电位/恒电流仪测量模拟孔电位,极化曲线表明模拟腐蚀坑处于钝化状态,即便是氧化膜破裂,腐蚀坑也发展得很慢.用pH计测量孔中pH的变化,并得到其工作曲线,此曲线表明带有氧化膜的点蚀坑坑内存在明显的酸化现象.并对A0铝池壳的服务寿命进行了估计.     

Formation of nanostructured YSZ/Ni anode with pore channels by plasma spraying

YSZ/Ni is the conventionally most used material for making the anode of a solid oxide fuel cell. Agglomerated nanostructured YSZ/NiO powders and plasma spray are applied to produce nanostructured YSZ/NiO coatings on porous support substrates. After reduction in an ambient atmosphere of 7% hydrogen and 93% argon at about 800 °C for 4 hours, a novel SOFC anode with nanostructured characteristics such as nano YSZ particles, nano Ni particles, nano pores and nano pore channels is produced. This new YSZ/Ni anode provides larger triple phase boundaries for hydrogen oxidation reactions. X-ray diffraction patterns of these YSZ/NiO coatings after 1 h of heat treatment at temperatures from 700 to 1100 °C are obtained and Scherrer analysis is conducted to study the effect of temperature on grain size. The results obtained from SEM, TEM, XRD and EDX measurements and analyses are presented in this investigation.