Round-Robin Test on methods for determining chloride transport parameters in concrete

This paper presents the results of a Round-Robin Test on methods for determining chloride transport parameters in concrete, carried out by the Technical Committee TC 178-TMC: “Testing and Modelling Chloride Penetration in Concrete” in which 27 different laboratories around the world have participated, using 13 different methods, in triplicate specimens, for 4 different mixes of concrete cast with different binders. Four different groups of methods have been tested: Natural diffusion methods (D), Migration methods (M), Resistivity methods (R) and Colourimetric methods (C). The statistical treatment of the data has been carried out according to the International Standard ISO 5725-2:1994 for the determination of the accuracy (trueness and precision) of measurement methods and results. Part 2: Basic method for the determination of the repeatability and reproducibility of a standard measurement method. In order to make an evaluation of these methods, four indicators have been identified and within each of them, several sub-indicators have been assigned. According to this system of classification, the methods have been classified following each indicator (trueness, precision, relevance and convenience), and also globally, by assigning different factors of importance, F.I., to the different indicators.     

Leakage tests for Am solid sources used for liquid xenon detector monitoring

Experimental tests are described to check solid ²⁴¹Am radioactive sources used to monitor operation of liquid xenon detectors. In particular, radioactive leakage was tested in extreme temperature conditions following immersion in liquid nitrogen for different time periods. No radioactivity loss was detected from the sources considered. The paper describes the source characteristics, test methods and results obtained.     

Comparison of structural and photoluminescence properties of ZnO thin films grown by pulsed laser deposition and ultrasonic spray pyrolysis

ZnO thin films have been deposited by pulsed laser deposition (PLD) and ultrasonic spray pyrolysis (USP) method, respectively. X-ray diffraction and transmission electron microscopy characterizations indicate that ZnO film grown by PLD exhibits better crystallinity than that grown by USP. Photoluminescence spectra show that the near-band edge ultraviolet emission of film grown by PLD is narrower and shifts to higher energy, compared with that of film grown by USP. In the visible range, ZnO film grown by PLD exhibits four local level emission centered at 470 nm, 486 nm, 544 nm, and 613 nm, respectively, while the film grown by USP only presents a weak broad band emission centered at 502 nm. Hall measurement shows higher carrier density and lower hall mobility in ZnO film grown by PLD than that in film grown by USP. The higher density of intrinsic defects as well as higher crystallintiy is considered to account for the difference of photoluminescence in ZnO film grown by PLD with that in film grown by USP.     

低速旋转机器振动测试与评价

低转速机器振动频率低、幅值小,测量困难.在考察转子的平衡情况时,不能仅通过振动幅值的大小来评价转子的平衡状况,而应该通过试加重量计算加重灵敏度以后,再计算出转子残余不平衡量并与标准要求值进行比较和判断.     

学生成绩评定方法研究

分别用x2拟合检验法、直方图和Q-Q分布图从直观和理论两方面出发验证学生成绩是否呈正态分布,通过图象与应用概率统计知识有机结合,运用数学软件对数据进行处理,达到验证研究的目的。     

铝电解槽热平衡测试计算中的几点问题

由于缺乏正规的标准，铝电解槽能量平衡测试中存在着一些概念混淆、计算方法和公式错误的情况，应引起测试工作者的注意，在测试计算前应认真制订方案，多查一些参考资料，核实所用公式、数据，避免发生失误。同时对于类似计算，由于计算机的应用，应尽可能采取精确算法。没必要采取一些非常粗糙的近似算法和经验值。     

Dynamics of electrically charged transient evaporating sprays

The evolution of an evaporating spray plume typical of those under consideration for use in direct injection spark ignition (DISI) engines, for early and late fuel injection strategies is investigated. Here the effect of electric charge, present on individual drops, upon the spray dispersal and evaporation rate is investigated with the aim of optimizing these parameters with respect to typical engine timescales and injection strategy. The predictions suggest that applying electric charge to drops in sprays injected early into the intake stroke does not have a beneficial effect. The spray evaporation rate is not significantly enhanced, and the long time interval between fuel injection and ignition actually promotes spray wall deposition. Conversely, applying electric charge to sprays injected late encourages secondary atomization and the increase in surface area greatly improves the evaporation rate. This is also true at higher engine speeds, corresponding to a much reduced time between fuel injection and ignition. Therefore it is suggested that the selective use of electric charge is viable way of tuning the spray character without effecting fuel metering when moving from an early to a late injection strategy in DISI engines when variable loads are required. Copyright © 2006 John Wiley & Sons, Ltd.     

喷射沉积柱坯的生长模型

根据现有喷射沉积设备的喷射几何关系推导了柱状沉积坯生长的数学模型,并利用该模型对沉积器的临界下降速度进行了初步估算。     

级数sum from n=1 to ∞(α(α-1)…(α-n+1)x~n/n!)在x=±1处的敛散性研究

用比较原则及莱布尼兹判别法对函数f(x)=(1+x)α的马克劳林级数在x=±1的敛散情形给予讨论.     

Nonlinear seismic response analysis of reinforced concrete tube in tube structure

Super-highly reinforced concrete tube in tube structure is a developing structure system of high-rise building. The more reasonable derivation process of the multi-vertical-line-element model stiffness matrix is given.On the premise of pointing out the problems of present multi-spring element model, combined with present multivertical-line-element model for analyzing on shear wall, the model is expanded to spatial one, and the stiffness matrix of which is derived. Combined with hysteretic axial model and hysteretic shear model, it is suitable for columns,wall limbs and beams with all kinds of section form. Some examples are calculated and compared with test results,which shows that the models have relatively good accuracy. On the base of the experimental phenomenon and failure mechanism for tube in tube structure specimen, nonlinear seismic responses analysis program on the basis of the advantaged element model for tube in tube structure is developed. Calculation results are in good agreement with those of the pseudo-dynamic tests and the failure mechanism can be well reflected.