An improved practice to manufacture Al–Ti–B master alloys by reacting halide salts with molten aluminium

The well-established “halide salt” route was employed in the present work to produce Al–Ti–B grain refiner alloys with consistent, good properties. The holding step in the production cycle was revised, however, to avoid oxidation of the molten alloy which is believed to be responsible for the relatively low Ti recoveries and thus for the inadequate and inconsistent grain refining efficiency. Stirring during holding was found to degrade the grain refining properties when molten potassium aluminium fluride salt was left on the molten alloy to avoid excessive oxidation. Likewise, holding temperatures higher than 800 °C and holding times longer than 30 min both had an undesirable effect on the grain refining performance. The experimental Al–5Ti–1B grain refiner alloy produced according to the present method provided consistent and better overall grain refining performance.     

TENSILE FRACURE IN AN Al-Li ALLOY 8090

ＴＥＮＳＩＬＥＦＲＡＣＵＲＥＩＮＡＮＡｌ－ＬｉＡＬＬＯＹ８０９０￥Ｊｉａｎｇ，Ｄａｍｉｎｇ；Ｗａｎｇ，Ｙｉｎｏｎｇ；Ｈｏｎｇ，Ｂａｎｄｅ；Ｌｅｉ，Ｔｉｎｇｑｕａｎ（ＨａｒｂｉｎＩｎｓｔｉｔｕｔｅｏｆＴｅｃｈｎｏｌｏｇｙ，Ｈａｒｂｉｎ１５００８０）Ｓｕ...     

电场固溶对2091A1-Li合金显微结构的影响

用电子探针及透射电镜研究了２０９１ＡｌＬｉ合金的电场固溶对显微结构的影响。结果发现，电场固溶通过促进含铜相溶解提高铜元素的固溶程度，加剧Ｌｉ原子在晶界上的非平衡偏聚，导致析出相δ′分布不均匀，体积分数减少，晶界上出现粗大的δ平衡相，Ｔ１及Ｓ′相均匀弥散分布，合金的力学性能（Ｔ６）达到了应变时效处理（Ｔ８）的水平。     

Development of design principles for a creep-limited alloy for turbine blades

Recent advancements in turbine-blade materials engineering are reviewed in light of general superalloy research and the author’s work on a new powder metallurgy IN-792 creep-limited alloy for application in blades of gas-turbine engines. The developed set of principles presented in this paper incorporates all the factors that must be taken into consideration in selecting and designing an alloy for turbine blades.     

ZL114铝合金激光--龟弧的复合焊接

设计了一种激光-电弧复合热源焊接ZL114合金的新工艺，并对焊后的试件进行了X光检测、抗拉强度和全相组织等实验。结果表明，该种新工艺对铝合全有良好的适应性和可行性，是焊接领域的一个趋势。     

Leaded brass rods C 38500 for automatic machining operations: A technical report

C 38500 is a widely used copper alloy with a great variety of applications from decoration and architecture to mechanical/electrical engineering. The chemical composition of this alloy offers superior machinability and subsequently increased productivity in high-speed machining and manufacturing processes. In European countries, this alloy is used primarily as free cutting brass (CW 614N according to EN 12164: 1998), similar to C 36000 alloy, which is used also for thread rolling. The lower percentage of Cu compared to C 36000 (nominal 58% instead of 61%) decreases the cost of the raw materials. This paper reports the principal aspects of microstructure, mechanical properties, and machinability of this alloy in relation to the industrial manufacturing process used.     

热处理对Ag—15Al固溶体短程有序度的影响

研究了热处理对Ag-15Al(at％)固溶体合金电阻率和有序参数的影响,由X射线衍射分析表明,合金的短程序转变不是Ag_3Al化合物型的δ第二相的形成,而是α-Ag-Al固溶体原子的有序排列。     

工程机械用800MPa低合金高强度钢焊接接头断裂韧性评价

对调质状态800MPa低合金高强度钢及其焊接接头进行了系列温度的断裂韧性测试,讨论不同焊接方法对焊接接头断裂韧性的影响。发现板材的轧制方向对断裂韧性影响显著,LT方向试件的断裂韧性远超过TL方向试件的断裂韧性。在-60℃以上,母材处于上平台延性断裂范畴。在-80℃,裂纹扩展过程中有延脆断裂模式的转变。焊条电弧焊焊缝的断裂韧性与气体保护焊焊缝的断裂韧性相当。尽管常温下焊缝金属的断裂韧性甚至优于母材,但随着试验温度的降低,焊缝金属的断裂韧性迅速下降。在-20℃已发生断裂模式转变,这在结构服役时要引起重视。本研究为大型工程机械的断裂安全评定奠定了基础。     

表面氧化层对TiMn1.25Cr0.25储氢合金活化性能的影响

通过TiMn1.25Cr0.25合金粉活化前在空气中暴露不同的时间,探讨了表面氧化层的形成对其活化性能的影响。活化测试结果表明：合金的活化难度随着合金在空气中暴露时间的延长而加大。俄歇电子能谱(AES)结果表明,在空气中暴露后的合金表面形成了一层大约6nm-10nm厚的表面氧化层,正是这层氧化层的形成加大了合金的活化难度。扫描电镜(SEM)结果表明合金的活化过程与合金的碎化有着密切的联系。