硫化锌纳米粒子的微乳液合成

介绍了微乳液制备纳米粒子的基本原理。对影响微乳液体系形成的主要因素如油相、水相、表面活性剂种类及用量等进行了研究，以表面活性剂TWEEN80和SPAN80作乳化剂，通过调整其比例控制乳化剂的HLB值，制备了乳化剂浓度为0.3mol/L、水/乳化剂比为6：1的W/O型庚烷/ST80/水微乳液体系。在此微乳液中制备了ZnS纳米粒子，采用TEM和XRD对超细样品的结构进行表征，表明得到的样品为β型立方晶系ZnS粒子、粒子粒径10-30nm。     

3,4-二甲氧基苯乙腈合成研究

介绍了 3,4 二甲氧基苯乙腈的合成方法 ,探讨了各种因素对反应收率的影响 ,产品总收率和质量分数分别大于 65 .0 %和 98%。     

刚性棒状全芳香液晶聚酯的合成及性质的研究

以溴和苯基取代的对苯二甲酰氯及2，2′-二甲基联苯-4，4′-二甲酰氯作为单体，分别与甲基、叔丁基、苯基取代的对苯二酚经熔融缩聚反应，合成一类具有刚性棒状结构的全芳香液晶聚酯。聚酯的热性质以TGA、DSC，热台偏光显微镜研究。所有的聚酯均为热致性液晶，它们具有相对较低的转变温度，在普通的有机溶剂中具有较好的溶解性质。     

Synthesis and Characterization of Nanosized ZSM-5 Zeolite with Mesoporous Carbon Nanotube as Templates

Preparation of nanocrystalline ZSM-5 has been proven possible with carbon matrix by using confined space synthesis. In combination with the hydrothermal method, by the use of a mesoporous carbon nanotube as the inert support material, ZSM-5 with SiO₂/Al₂O₃ ratios of 100 was successfully synthesized with an average crystal size of 27 nm. Their structures were preliminarily characterized by x-ray power diffraction (XRPD) and infrared spectroscopy (IR), and scanning electron microscopy (SEM), respectively. At the same time, we put forward the mechanism about the confined space synthesis in terms of the results.     

高速钢高温形变诱发析出的研究

本文探讨了高速钢在高温形变过程中碳化物析出的行为及奥氏体组织状态对析出的影响。用透射电镜和扫描电镜分析了不同热处理状态奥氏体的组织结构,分析了高温形变过程中碳化物析出的部位,颗粒尺寸及形态。试验表明, 碳化物主要在奥氏体的缺陷处呈点状和点列状析出,大小为20mμ。处于回复状态的奥氏体缺陷诱发碳化物析出,析出碳化物钉札缺陷阻止再结晶进行。当再结晶驱动力较大时,由于动态再结晶充分发展,使缺陷大量消除,碳化物析出显著地减少。     

A novel technique to prepare LiNbO3 at low temperature

Fresh niobium hydroxide was first precipitated from NbF₅ solution using an aqueous ammonium hydroxide under basic conditions. Then a simple procedure of mixing lithium and niobium hydroxides together and heating at a low temperature (400 °C) produced pure ultrafine single phase LiNbO₃ (LN). In the literature, this is the lowest temperature so far reported on the formation of LN. The phase content and lattice parameters are determined by X-ray diffraction (XRD). The average particle size and morphology were studied by transmission electron microscopy (TEM).     

Effect of C/Ti ratio on the laser ignited self-propagating high-temperature synthesis reaction of Al-Ti-C system for fabricating TiC/Al composites

TiC/Al composite was successfully synthesized utilizing laser ignited self-propagating high-temperature synthesis (SHS) of Al-C-Ti system with the different C/Ti molar ratio. When the molar ratio of C to Ti is below 1:1 in the starting materials, in addition to fine TiC particulates, a large amount of Al₃Ti phase was found in the composites; however, when the molar ratio of C to Ti is 1:1 in the starting materials, the Al₃Ti phase was almost completely eliminated and the distribution of TiC particulates generally appeared to be more homogeneous throughout the products synthesized.     

Formation of mushroom-like ZnO microcrystals through a solution calcination process

Mushroom-like ZnO microcrystals have been prepared via a solution calcination route, using Zn(NO₃)₂ as Zn source in the absence of any surfactants, templates or catalysts. This is the first example to prepare mushroom-like crystals as semiconductors, which are expected to show particular physical properties. The ZnO products were investigated by X-ray powder diffraction (XRD), scanning electron microscopy (SEM), Raman spectroscopy and photoluminescence (PL) spectrum measurements. A suitable concentration of Zn(NO₃)₂ solution was important for the growth of the mushroom-like products. The reported synthetic procedure is straightforward and inexpensive, and thus can be readily adopted to produce large quantities of mushroom-like ZnO microcrystals.