Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

软X射线对血液有形成分表面电荷的影响——2、淋巴细胞和血小板膜电荷的变化

软X射线不仅能引起红细胞表面电荷的变化,同时也能导致淋巴细胞和血小板表面电荷下降,表现为照射后它们的电泳率下降。低剂量范围内,这种电荷的变化是暂时性的,照后4小时降到最低点,24小时后恢复到对照的水平。细胞电泳率的下降与辐射剂量相关。淋巴细胞是一个复杂的细胞群,正常状态下,按细胞在电场中泳动速度的快慢,可分为两个组分:快峰为T细胞,慢峰为B细胞。软X射线照射以后,T和B细胞的电泳率皆减慢,频数分布峰值下降,离散度加大。血小板成分单一,电泳率较一致。 从照射浓集的血小板再加回自身血浆中电泳率的下降较照射血浆再加到血小板中的电泳率下降大得多;受照射的血小板在磷酸缓冲液中电泳率下降较在血浆悬液中严重得多;2000 rad照后,悬浮于血浆中的血小板电泳率能恢复,而悬浮于磷酸缓冲液中则不能恢复,三个方面来看,血浆中可能存在抗辐射因子。超氧化物岐化酶能有效地预防血小板电泳率的下降,从而可阻止血小板的凝聚。     

Three dimensional boundary element analysis of internal cracks under sliding contact load with a spherical indenter

Using boundary element based three dimensional modelling for linear fracture mechanics, we present an analysis of cracking in a homogeneous medium subject to contact load. The proposed iterative solution procedure allows a simultaneous treatment of a reasonable number of partially closed cracks. It is shown that the most probable direction of propagation of a vertical internal crack is strongly dependent on its size compared to the contact radius and its location with respect to the axis of maximum normal load.     

Pool boiling on a superhydrophilic surface

Titanium Dioxide, TiO₂, is a photocatalyst with a unique characteristic. A surface coated with TiO₂ exhibits an extremely high affinity for water when exposed to UV light and the contact angle decreases nearly to zero. Inversely, the contact angle increases when the surface is shielded from UV. This superhydrophilic nature gives a self-cleaning effect to the coated surface and has already been applied to some construction materials, car coatings and so on. We applied this property to the enhancement of boiling heat transfer. An experiment involving the pool boiling of pure water has been performed to make clear the effect of high wettability on heat transfer characteristics. The heat transfer surface is a vertical copper cylinder of 17 mm in diameter and the measurement has been done at saturated temperature and in a steady state. Both TiO₂-coated and non-coated surfaces were used for comparison. In the case of the TiO₂-coated surface, it is exposed to UV light for a few hours before experiment and it is found that the maximum heat flux (CHF) is about two times larger than that of the uncoated surface. The temperature at minimum heat flux (MHF) for the superhydrophilic surface is higher by 100 K than that for the normal one. The superhydrophilic surface can be an ideal heat transfer surface. Copyright © 2002 John Wiley & Sons, Ltd.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Finite element simulation of the mechanics of flat contact pad fretting fatigue tests

An understanding into the macro kinetic and kinematic behaviour of fretted surfaces is provided. Making use of a modified version of a previously developed in‐house two‐dimensional elastic–plastic finite element analysis numerically simulates flat contact pad fretting fatigue tests. Basic macro mechanics concepts are adopted to idealise two bodies with rough contact surfaces and loaded at two different sites with arbitrary axial loading profiles. A time scale factor is devised to recognise the earliest candidate out of the events possibly accommodated at each loading increment. The present analysis utilises a relevant experimental set up developed in the Structural Integrity Research Institute of the University of Sheffield as an application. Computational results accurate to within 1.2% and corresponding to one contact pad span and six constant normal loads acting individually with four amplitudes of two sinusoidal axial load cycles are presented. The present computations include (1) the development of the global and local normal and tangential reactions and relative sliding displacement acting along the fretting surfaces and (2) contact pad deformation, generated stress fields and plasticity development within the neighbouring region of the fretted area.     

浅谈下一代网络（NGN）

计算机网络的发展日新月异。下一代计算机网络（NGN）的探讨、研究已经成为当前的潮流。下一代网络是目前电信、互联网运营商和设备厂商都在讨论的热点技术，国内外许多网络运营商都在探讨，并正在或考虑建设试验网进行更深入的研究。本文介绍了NGN的定义、主要特点、分层结构和关键技术。     

Ohmic contact and transport properties of II–VI Green/Blue laser diodes

The employment of the Zn(Se,Te) pseudo-graded contacting scheme to p-type ZnSe-based alloys contributes directly to the recent demonstration of room temperature continuous-wave operation of II– VI green-blue laser diodes. Contact ohmicity is maintained down to cryogenic temperatures which enabled the investigation of electrical transport properties associated with the p-type nitrogen-doped ZnSe, Zn(S,Se), and (Zn,Mg)(S,Se). The observation of both persistent photoconductivity and a metastable population of holes which are in thermodynamic equilibrium with hydrogenic acceptors having reduced activation energy suggests the presence of a DX-like behavior for holes in p-type (Zn,Mg)(S,Se).     

磁性材料产业现状与展望

介绍磁性材料的主要品种，如永磁体、软磁体和磁记录介质材料的行业现状及技术进步。     

Influence of electroplating conditions on magnetic properties of Fe-36wt.% Ni alloy film

A Fe-Ni soft magnetic film was prepared in sulphate solution by electroplating. The influences of the molar ratio of n [Fe2+ ]/ n [Ni2+ ], current density, bath temperature, pH and L-ascorbic acid concentration on magnetic properties of Fe-Ni alloy film were investigated. The results show that the saturated flux density(BS) of the film increases initially and decreases after it reaches the specific value with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density, bath temperature and pH. However, the relationship between L-ascorbic acid concentration and B S keeps linear. It is observed that the coercive force( Hc) is enhanced with the increase of n [Fe2+ ]/ n [Ni2+ ] molar ratio, current density and pH. By comparison, when the bath temperature increases, Hc always decreases. With the increase of L-ascorbic acid concentration, the coercive force increases initially and then decreases.