Mean residence time of gas in mechanically agitated gas–liquid contactors

In the present study of gas–liquid contactors, mean residence/contact time was calculated from knowledge of superficial velocity and the gas phase hold-up, for various gas rates and impeller geometry and speeds, and compared with values obtained from RTD measurements. A new correlation, involving Flow Number, Froude Number, system geometry and the physical properties, is proposed. This uses the authors data and those available in literature.     

粉喷桩处理软弱地基在祁临高速公路的应用

结合工程实例，介绍了粉喷桩的所属类型，粉喷桩对软弱地基加固的原因，所适应土质及加固特点，阐述了祁临十八合同段的粉喷桩施工过程及施工中应注意的若干问题，得出粉喷桩处理不良地基效果良好。     

点阴极电场辅助阳极连接中的紧密接触面积和电流

用等效电路的方法研究了点阴极情况下的电场辅助阳极连接效应，计算了连接电流，连接孕育期和紧密接触面积，本文结果表明，连接初期电流迅速衰减，随后缓慢变小，直至某一稳定值，孕育期随温度上升指数下降，连接温度高时，孕育期将难以观察到；待连接表面之间紧密接触面积随时间延长而非线性扩展，紧密接触区域增大时，其边界向外推进速度渐小，而接触面积增加渐快。     

重载齿轮齿面疲劳损坏及预防

点蚀和剥落是重载齿轮齿面疲劳损坏最普遍的形式.根据齿轮失效分析实例,对齿面初始点蚀、破坏性点蚀和齿面剥落等三种主要疲劳损坏的特征、发生部位及破损危害程度进行了分析研究,较系统地论述了齿轮接触疲劳破坏机理,影响因素及其产生原因,并对有关的齿面破坏提出了相应的预防措施.     

Generation of Technology-Independent Retargetable Analog Blocks

This paper introduces a complete methodology for retargeting of analog cells to different sets of specifications. This methodology is technology-independent, thus allowing the migration, from one technology to another, of the circuit under retargeting. Careful integration of the device sizing and layout generation tasks via the incorporation of layout constraints during the sizing process allows to generate fully functional designs in a few minutes. The methodology is illustrated via the retargeting of a fully-differential Miller-compensated two-stage operational amplifier for a new set of specifications and two different technological processes.An erratum to this article can be found at     

An Effective Software Pipelining Algorithm for Clustered Embedded VLIW Processors

This paper proposes a software pipelining framework, CALiBeR (ClusterAware Load Balancing Retiming Algorithm), suitable for compilers targetingclustered embedded VLIW processors. CALiBeR can be used by embedded systemdesigners to explore different code optimization alternatives, that is, high-qualitycustomized retiming solutions for desired throughput and program memory sizerequirements, while minimizing register pressure. An extensive set of experimentalresults is presented, demonstrating that our algorithm compares favorablywith one of the best state-of-the-art algorithms, achieving up to 50% improvementin performance and up to 47% improvement in register requirements. In orderto empirically assess the effectiveness of clustering for high ILP applications,additional experiments are presented contrasting the performance achievedby software pipelined kernels executing on clustered and on centralized machines.     

软X射线对血液有形成分表面电荷的影响——2、淋巴细胞和血小板膜电荷的变化

软X射线不仅能引起红细胞表面电荷的变化,同时也能导致淋巴细胞和血小板表面电荷下降,表现为照射后它们的电泳率下降。低剂量范围内,这种电荷的变化是暂时性的,照后4小时降到最低点,24小时后恢复到对照的水平。细胞电泳率的下降与辐射剂量相关。淋巴细胞是一个复杂的细胞群,正常状态下,按细胞在电场中泳动速度的快慢,可分为两个组分:快峰为T细胞,慢峰为B细胞。软X射线照射以后,T和B细胞的电泳率皆减慢,频数分布峰值下降,离散度加大。血小板成分单一,电泳率较一致。 从照射浓集的血小板再加回自身血浆中电泳率的下降较照射血浆再加到血小板中的电泳率下降大得多;受照射的血小板在磷酸缓冲液中电泳率下降较在血浆悬液中严重得多;2000 rad照后,悬浮于血浆中的血小板电泳率能恢复,而悬浮于磷酸缓冲液中则不能恢复,三个方面来看,血浆中可能存在抗辐射因子。超氧化物岐化酶能有效地预防血小板电泳率的下降,从而可阻止血小板的凝聚。     

构造作用对油气生成和运聚的影响

有机质从埋藏开始，就处于极其复杂的地球物理化学场中，环境提的能量，一是热量，二是机械能，机械能，主要是通过机械力作用传递给系统的，另外还以机械波的形式赋予系统一定的机械能。当发生断褶构造运动时，机械力对油气运移的影响尤为突出，它经能量的迁移转化，促成了包括机械力降解和地应力驱动等一系列的连锁反应，制造了一次次高效的成油（生运）事件，本文以突变论为着眼点，按照改造控制建造的思路，大胆提出构造运动制造生排烃事件，成就含油气系统的假说。     

回转升降生物接触工艺的实验研究

提出了一种具有特殊运转方式的新型RBC系统－－回转升降生物接触工艺，对回转升降生物接触工艺的工作原理和工艺特征进行了论述。并通过动态实验，对回转升降生物接触工艺小型实验装置的性能和效果进行了初步考察。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.