带曲率补偿的带隙基准电流源的设计

简单介绍了带隙基准源的基本原理,给出了一款基于Widlar结构的带曲率补偿的带隙基准电压电流源的设计方法,通过采用TSMC₀.5μm工艺库对电路进行仿真,在-40～150℃的温度范围内,其带隙基准的输出具有12ppm/℃的温度系数,电流基准的输出具有42ppm/℃。此外,文中还对曲率补偿电路的工作原理进行了分析,并且通过仿真波形对曲率补偿的工作机制进行了讨论。     

模拟集成温度传感器设计

介绍了一种模拟集成温度传感器的电路设计。该电路利用双极性晶体管基极-发射极结压降与热力学温度T成比例的关系来实现温度的测量,并在6μm双极工艺线上投片成功。该电路在常温25℃下输出298.2μA的电流,在-55℃～150℃的工作温度范围内的误差不超过±3℃,非线性度误差不超过±0.4℃。     

矿用隔爆兼本质安全型不间断直流稳压电源的设计

基于本质安全型电源的原理及特点,提出了一种矿用隔爆兼本质安全型不间断直流稳压电源的设计方案,详细介绍了该电源主要电路的设计。该电源采用LM317可调稳压芯片实现稳压功能,具有使用方便、电路简单、变换效率高、成本低等优点。测试结果表明,该电源达到了本安标准,满足了安全型电气设备的需求。     

卧螺离心机变频调速PLC控制系统设计

针对传统的卧螺离心机控制系统存在稳定性差、工作效率低的问题,设计了一种卧螺离心机变频调速PLC控制系统;详细介绍了该系统中共直流母线变频调速系统、副电机随动方案及负载率调整方法、PLC控制系统、组态界面的设计。实际应用表明,该系统运行稳定,提高了离心机的性能。     

Citations do not solve problems.

D. T. Cambell and D. W. Fiske (1959) made the now-obvious statement that measures of the same variable made by different methods should agree (converge) and certainly should agree better than measures of different variables made by those several methods. Almost everyone accepted that statement, yet the multitrait–multimethod matrices published today show little or no improvement over the published examples cited in 1959. The article raised the conceptual problem of how a variable and its measurement should be linked and the methodological problem of clarifying the nature of methods and their effects. Given these unresolved problems, it is perhaps not surprising that the question of the appropriate statistical analysis of these matrices has also no consensual answer. Perhaps methods and traits or contents are so thoroughly intertwined that their interaction cannot be adequately analyzed. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

基于环探头测量含运动导体的瞬态电流波形

电流除了用罗果夫斯基线圈进行测量外,还可通过环探头测量电流产生的磁场来计算得到。直线电机除了位置固定的母线导体外,还有沿母线运动的电枢;母线回路注入脉冲电流后,电枢会被加速而运动。简化母线和电枢为线电流模型,在长线模型基础上,通过环探头测量得到的磁场计算出近似电流波形。因为探头所测磁场主要由其附近电流所贡献,所以合理配置电枢起始位置与探头位置后,电枢运动对电流测量的影响很小。在瞬态电流上升沿、平台区和下降沿的不同阶段,利用实验折算的系数,可得到时域瞬态电流波形,其测量结果与用罗果夫斯基线圈测量波形一致。     

基于DSP嵌入式技术的无刷直流电动机智能控制系统的研究

本文以TI公司的数字信号处理器TMS320F2812作为核心控制芯片,设计出了一款低成本具有足够功能的无刷直流电动机的调速控制系统实验平台。详细介绍了该控制系统的软硬件结构及控制策略。通过对该控制系统实验结果的分析,表明该系统的动态性能和稳态性能好,抗干扰能力强的特点,且在该实验平台上可进行一些先进控制算法的研究。     

Overview of Tiber-II—Evolution toward an Engineering Test Reactor

TIBER II is designed to be a minimum size and cost candidate for an international Engineering Test Reactor. High-current density Nb₃Sn superconducting magnets with radiation-tolerant polymide insulation is combined with a minimum thickness tungsten inbored shield and a common, external vacuum boundary to minimize the inner radial build of the tokamak core. This results in a major radius of 3 m, compared to 5 m for previous ETR designs such as INTOR, with correspondingly lower costs expected. Cyclic stress fatigue limits the number of pulses so that steady-state current drive, based on a combination of neutral beams, lower hybrid and ECH, is designed to achieve reactor-relevant nuclear testing conditions (Fluence 3MW yr/m², rwall > 1 MW/m² in steady state).This report is abstracted from a more complete information document UCID-20863 with numerous authors. See Ref. l for complete credits.     

Continuous electromagnetic separation of inclusion from aluminum melt using alternating current

A novel scheme about the continuous electromagnetic purification of aluminum melt was put forward based on the utilization of a square separation pipe and a 50 Hz alternating current to produce electromagnetic force. It is experimentally found that with electrical current of 400 A/cm^2, it takes only 10 s to remove 95% inclusion from aluminum melt. Comprehensive numerical simulations were carried out to investigate the dynamics mechanisms behind the process. The results show that the removal of inclusion is attributed to the cooperative effects of electromagnetic buoyancy and the secondary flow induced by the rotational electromagnetic force, and the removal efficient increases with the size of inclusion and the electrical current imposed. Theoretical predictions on the distribution and removal efficiency of inclusion were supported by the experiments.     

杂散电流对阴极保护效果影响的模拟实验

本文通过模拟地下管道阴极保护的现场，测定了地下的杂散电流及其对阴极保护效果的影响，并对相关问题进行了分析。