硅表面上的纳米量子点的自组织生长

纳米半导体量子点以其所具有的新颖光电性质与输运特性正在受到人们普遍重视。作为制备高质量纳米量子点的工艺技术 ,自组织生长方法倍受材料物理学家的青睐。而如何制备尺寸大小与密度分布可控的纳米量子点更为人们所注目。因为这是关系到纳米量子点最终能否器件实用化的关键。文中以此为主线 ,着重介绍了各种 Si表面 ,如常规表面、氧化表面、台阶表面以及吸附表面上 ,不同纳米量子点的自组织生长及其形成机理 ,并展望了其未来发展前景     

多层频率选择表面的分析

本文利用矩量法和广义散射矩阵理论分析了多层频率选择表面的散射特性。通过引入广义波导概念,可以统一分析单元形状为任意的多层频率选择表面。作为示例,计算了几种不同结构频率选择表面的散射特性,结果与文献中给出的数据相符。     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

光通信用垂直腔面发射激光器的进展

垂直腔面发射激光器(VCSEL)以其优异的性能有望成为信息时代的新光源.文章介绍了用于光通信的VCSEL的开发现状.     

SiC颗粒增强铝基复合材料切削表面分形维数及其与抗磨损性能的关系

做为一种耐磨性能很好的材料 ,SiC颗粒增强铝基复合材料切削加工表面具有分形特征。实际研究表明SiC颗粒增强铝基复合材料切削加工表面分形维数与抗磨损性能有密切关系 ,本文还分析了表面分形维数越大其抗磨损性能越强的机理。     

过共晶Al－Si合金共生区激光表面处理

用２ｋＷ连续ＣＯ２激光对过共晶Ａｌ－１８Ｓｉ合金以不同能量密度和扫描速度进行快速熔凝处理。用扫描电镜、电子微区分析仪分析了微观结构。从计算机对Ａｌ－Ｓｉ合金ｆ－ｎｆ系统的非平衡理论计算所得的共生区及实验结果的分析可见，当能量密度和扫描速度决定的凝固条件处于共生区中部时，过共晶Ａｌ－Ｓｉ合金激光表面处理可以得到共晶间距低于２００ｎｍ的完全共晶结构。     

面流消能近底紊动流速特性的研究(面流消能试验研究之一)

本文主要论述了面流消能五种典型流态近底紊动流速特性,总结出了近底时均流速和紊动强度沿程变化规律,提出了近底紊动流速可能出现的最大瞬时值及相应位置的计算公式。面流消能工程的下游防冲设计中考虑的主要水力参数之一是,消能段近底流速紊动可能出现的最大瞬时值及其相应的部位,但目前国内外研究成果较少。笔者通过水工模型试验重点研究了面流消能各典型流态近底流速及其紊动纵向分量沿程的变化规律,并提出了计算公式,为优化面流设计提供科学依据。     

TiO_2载体表面酸性的研究

利用NH_3吸附和吡啶吸附红外技术研究TiO_2的制备条件对其表面酸性的影响。结果表明,用NH_3水中和TiCl_4溶液方法制备的TiO_2(A)表面有较强的L酸中心,中和条件对表面酸性中心数目和强度有显著影响。由TiOSO_4水解方法制备的TiO_2(B)表面具有较强的L酸中心和较弱的B酸中心,引入不同添加剂可有效地调变TiO_2载体表面的酸性。     

Nitrogen addition to iron powder by mechanical alloying

Nitrogen was alloyed into iron (a) by mechanical processing in a nitrogen gas environment, and (b) by mechanically alloying with iron-nitride powders to characterize resulting nano-structure and nitrogen distribution. Although the infused nitrogen concentration was significantly greater than the thermodynamic equilibrium solubility of iron, no nitrides formed, even for nitrogen concentrations as high as 4.1 wt.% However, a bctFe phase did form. Lattice expansion calculations indicate that the sum of the interstitial bcc-Fe and bctFe nitrogen concentrations was significantly less than the total measured nitrogen concentration. A considerable portion of the mechanically infused nitrogen was determined to be associated with nanograin boundaries.     

Evolution of BET internal surface area in glassy carbon powder during thermal oxidation

It is demonstrated that glassy carbon powder can be thermochemically activated. During activation, a film with open pores is created on the glassy carbon particles. This film has a large internal surface area, which is accessible to liquids and gases. A simple model for the evolution of the internal surface area in glassy carbon powder during thermochemical gas-phase oxidation is also presented and compared with experimental data. Experimental results are in qualitative agreement with the model. We found that a sharp particle size distribution is desirable with regard to potential technical applications.