Semiflexible random thermotropic copolymers from 8‐(3‐hydroxy phenyl) octanoic acid and 3‐chloro‐4‐hydroxy benzoic acid/3,5‐dibromo‐4‐hydroxy benzoic acid

Two series of semiflexible random thermotropic copolymers containing 8‐(3‐hydroxy phenyl) octanoic acid (HPOA) with either 3‐chloro‐4‐hydroxy benzoic acid or 3,5‐dibromo‐4‐hydroxy benzoic acid were prepared by melt polycondensation techniques. The copolyesters were characterized with Fourier transform infrared spectroscopy, dilute solution viscometry, hot‐stage polarized light microscopy, differential scanning calorimetry, thermogravimetric analysis, and wide‐angle X‐ray diffraction. Studies revealed that the amount of HPOA as a disruptor incorporated into the backbone of substituted 4‐hydroxy benzoic acids had a detrimental effect on the liquid‐crystalline behavior. Mesophase‐transition temperatures were observed between 210 and 250°C, and the optical textures were of typical nematic phases. The degree of crystallinity decreased with an increase in the HPOA content. The thermal stability of the copolymers was in the range of 310–370°C. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Studies on jute–asphalt composites

The tensile properties of jute make it a suitable raw material for asphalt overlay (A/O) fabric. In this study, the thermal stability of jute under conditions of asphalt overlaying process was investigated and the compatibility of jute with asphalt was assessed through experimentation on jute–asphalt composites under mechanical and hygral loads. Fourier transform infra red (FTIR) spectroscopic study revealed probable chemical bonding between jute and asphalt. The test for ascertaining the capability of asphalt encasement for protecting jute against biodegradation under enzymatic attack was found positive. A 6‐month hygral treatment, of the jute–asphalt composite, showed significant increase in modulus of the material. The results indicate that although the strength of jute deteriorates by about 10% under asphalt overlaying condition, the overall tensile behavior of jute fabric–asphalt composite material is considerably superior to that of the pure jute fabric, even under biological and extended hygral loading conditions. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci 2008     

Sheet molding compound characterization using spiral flow

Sheet molding compound (SMC) is a fiber‐reinforced polymeric composite. It is often used in automotive, marine, and industrial applications over other materials because of its high strength to density ratio, resistance to corrosion, and low cost. There is a demand in the SMC industry to be able to characterize SMC processability. This is particularly true for heavy truck body panels, one of the fastest growing applications of SMC. Because of their large size and high strength requirement, the molding forces have a major influence in the molding cycle. Also because of the long flow paths involved, the ability of the paste to carry glass needs to be properly characterized when developing new SMC materials. In this article, we demonstrate the benefits of using spiral flow as a processability tester. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Synthesis and thermomechanical characterization of polyurethane elastomers extended with α,ω‐alkane diols

A series of polyurethane (PU) elastomers was prepared by the reaction of poly(?‐caprolactone) and 4,4′‐diphenylmethane diisocyanate, which was extended with a series of chain extenders (CEs) having 2–10 methylene units in their structure. The completion of the reaction was confirmed by Fourier transform infrared spectroscopy. The chemical structures of the synthesized PU samples were characterized with Fourier transform infrared, ¹H‐NMR, and ¹³C‐NMR spectroscopy, and the thermal properties were determined by thermogravimetric analysis, DSC, and dynamic mechanical thermal analysis techniques. The mechanical properties were also studied and are discussed. The thermogravimetric analysis and DSC analysis showed that CE length had a considerable effect on the thermal properties of the prepared samples. The dynamic mechanical thermal analysis and damping peaks were also affected by the number of methylene units in the CE length. The elastomer extended with 1,2‐ethane diol exhibited optimum thermal properties, whereas the elastomer based on 1,10‐decane diol displayed the worst thermal properties. Tensile strength and elongation at break decreased with increasing CE length, whereas hardness showed the opposite trend. The glass‐transition temperature moved toward lower temperatures with increasing CE length. The decrease in the glass‐transition temperature and tensile properties were interpreted in terms of decreasing hard segments and increasing chain flexibility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

橡胶Mooney—Rivlin模型材料系数对轴向刚度影响分析

在橡胶小变形范围内，采用理论推断的方法，得到在相同硬度下橡胶Mooney—Rivlin模型材料系数由C2／C1决定的关系式。并采用ABAQUS有限元软件分析的方法，结合橡胶轴向刚度常规解，分析了C2／C1不同值对橡胶轴向刚度的影响进行，结果显示其影响呈现一定规律性。     

Computational materials: Multi-scale modeling and simulation of nanostructured materials

The paper provides details on the current approach to multi-scale modeling and simulation of advanced materials for structural applications. Examples are given that illustrate the suggested approaches to predicting the behavior and influencing the design of nanostructured materials such as high-performance polymers, composites, and nanotube-reinforced polymers. Primary simulation and measurement methods applicable to multi-scale modeling are outlined. Key challenges including verification and validation are highlighted and discussed.     

Computer aided kinetic modeling with KMT and KME

The complexity of many chemical and refining reaction systems and the thus-derived tedious and time-consuming process of building the associated kinetic models have been major obstacles in the use of fundamental kinetics in the solution of chemical engineering problems. This review summarizes work aimed at removing theses obstacles. Our recent work that has led to the enhancement of the Kinetic Modeler's Toolbox (KMT) and the development of the Kinetic Model Editor (KME) presents an end-to-end solution to the kinetic modeling process, including automated feedstock modeling, reaction network construction, kinetic rate estimation, model programming, process system configurations, model customizations, compilations, model execution and results analysis.     

利用茚三酮或DFO加强显现热敏纸张上的潜在指纹

本文介绍一种新技术——利用茚三酮或DFO加强显现热敏纸张上的潜在指纹。大部分热敏纸张的热敏剂表面,使用DFO或茚三酮石油醚溶液(NPB)显影时将会变黑。显现的指纹和背景之间反差很小。新技术介绍了在指纹和热敏层之间,用丙酮水洗,可以去掉黑色污斑。其它新的化学试剂漂洗,显现的指纹有清晰的纹线和很高的反差。大量使用这种技术,可以使试剂优化,成本降低,短时间内能处理大量检材。工作试剂包括商用、不挥发、含氮的有机化合物,也使用象NPB这样的浸透性试剂。     

Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.