溢流反弧段水流边界层有关概念的探讨

本文对溢流反孤段水流边界层的定义方法进行分析讨论。在分析及弧段流速分布的基础上提出离心力附加边界层厚度和粗糙度附加边界层厚度的概念,研究了壁面曲率和壁面粗糙度对溢流反弧段边界层发展的影响。     

Machining with tool–chip contact on the tool secondary rake face—Part II: analysis and discussion

The forces, chip thickness, and natural tool–chip contact length in machining with a double-rake-angled tool are predicted in Part II of the present study. It is revealed that in comparison with a single-rake-angled tool, a double-rake-angled tool increases the forces, especially the thrust force. However, the increase in chip thickness and tool–chip contact length is not significant under the input conditions specified in the present study. The effect of seven input variables of the proposed model is quantitatively investigated. The predicted variations of forces, chip thickness, and natural tool–chip contact length are in good agreement with theoretical and experimental results obtained by other researchers. The interrelationships among the resultant force, the chip thickness, and the natural tool–chip contact length are established, which provides a new and promising method to estimate the tool–chip contact length by employing the resultant force. It is demonstrated that the model can also be extended to study the problem of machining with a groove-type chip breaker tool.     

Energy absorption in splitting square metal tubes

This paper presents an investigation into the energy absorbing behaviour of axially splitting square metal tubes. Tubes 50 mm square with a variable thickness were pushed slowly against rigid pyramid shaped dies, which had various semi-angles. By pre-cutting 5 mm long slits at the four corners, the tube splits along the corners and curls outward with a certain radius at a constant force. In this energy dissipating system, there are three components: tearing energy, plastic deformation energy and frictional energy. Theoretical analysis of the three energy components is presented. Curl radius is also studied in detail. Good agreement between experiments and theory is obtained. The results show that tubes which both split and curl may be used as efficient, long stroke energy absorbing devices.     

Effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy

The CuCrZr alloy undergoes processes of precipitation during ageing. Besides precipitation hardening the strength is affected by cold deformation which is performed before and after ageing. The cold deformation (D ₁) before ageing accelerates the process of strength hardening, since it induces higher rate of precipitation from the saturated a-sold solution. Cold deformation (D ₂) after ageing primarily affects the alloy strength. In this paper the results of the effect of thermomechanical treatment on mechanical properties and electrical conductivity of a CuCrZr alloy are presented. The aim of the paper was to evaluate the most suitable combination of thermomechanical treatment and alloy properties.     

粘弹性圆柱壳在轴向恒压下的动力稳定性

基于Timoshenko-Mindlin假设,得到考虑粘弹性的各向同性圆柱壳及纤维增强正交铺设层合圆柱壳在轴向恒压下的动力学方程。文中对两端简支的圆柱壳进行了分析,依Laplace变换,导出动力稳定的特征方程,由Routh-Hurwitz判据建立动力稳定性条件,对两类圆柱壳讨论了横向剪切变形的影响。     

混凝土简支梁预设变形值探讨

以某高速公路钢筋混凝土与预应力混凝土工程为例，从简支梁的预拱度和下挠度的设置两方面进行了阐述，提出了钢筋混凝土简支梁下挠变形和预应力混凝土简支梁上拱变形的不同之处。     

碎丝埋弧焊在大型立式储罐中的应用

大型储罐底板焊接及变形控制是保证储罐整体施工质量的关键环节,采用碎丝填充的焊接方法可以防止变形,同时可以有效地避免应力集中,提高施工质量。文章介绍了碎丝埋弧焊的原理、工艺参数和焊接方法。实践证明,填充碎丝不仅是一种减小底板焊接变形的手段,同时可以充分利用焊接热能,节约焊接时间和焊剂用量,经济效益好,是一种值得推广的技术。     

临南油田夏52块沙三中泥质砂岩油层精细评价

临南油田夏 5 2块沙三中泥质砂岩油层分布广 ,未动用程度高 ,为了稳定产量 ,急需寻找可直接投产的泥质砂岩油层。本文利用相渗实验资料建立油相相对渗透率与含水饱和度关系 ,从而建立有效渗透率的解释模型。依据有效渗透率和有效厚度将泥质砂岩油层划分等级 ,分区评价 ,这不仅有利于合理开采和保护此类油层 ,降低其生产成本 ,也为预测此类油层产能提供依据     

几何非线性复合材料层合固体壳单元

通过定义广义应力,提出了一个改进的刚度矩阵,以克服固体壳元的厚度自锁问题,并能保证沿复合材料层合结构厚度方向上的连续应力分布;将应力插值函数分为低阶和高阶两部分,建议了一个新的非线性变分泛函,推导了一个用于几何非线性分析的九节点固体壳单元,该单元的计算精度和效率基本上与九节点减缩积分单元相当,与同类型其他单元相比,该单元显著提高了计算效率。     

汽车摩擦片厚度测量装置驱动电路的研究

本文通过对摩擦片厚度在线测量装置系统构成的全面分析，对其驱动电路子系统进行了理论探索和技术研究，完成了相应的电路设计、误差分析及器件选择等工作，并进行了具体的实验验证，证明该驱动电路具有良好的性能，可圆满实现摩擦片厚度在线检测和实时分析的工作任务。