Influence of Polyalkylmethacrylate VII on Boundary Film Formation,Friction,Wear and Efficiency of Lubricants

1 Influence of PAMAon Boundary Fil mFormation and Friction1.1 Experi mental methodsUltra-thin optical interferometry has been used tostudy thinlubricating fil ms for more than a decade and theexperi mental details of this technique have been reportedpreviously[1].The principle of the test setup is shown inFigure1.A polished steel ball is loaded and rolled againstthe flat surface of a glass disc that is coated with a thinsemi-reflecting chromiumlayer and a silica spacer of about500nmthickne…     

工业管道测厚的几点问题探讨

超声波测厚在腐蚀监测上应用越来越广泛,为让这项检测技术更准确、更可靠,充分发挥功效,文章就工业管道测厚中测厚数据处理、测厚点选择、高温问题以及其它影响因素等几个方面进行了探讨。     

X60管线钢疲劳特性的研究

利用2、4和14mm的X60钢紧凑拉伸试样进行同样应力水平、固定应力比（R＝0．1）的疲劳裂纹扩展试验，揭示出高韧性管道钢的疲劳裂纹扩展存在显著的厚度效应。由于应力水平低，相应的离面应力也低，不足以导致分层开裂，因此，裂纹端部的三维应力约束随厚度增加而增大。4mm试样的疲劳裂纹速率远高于2mm试样，但厚度再增大，裂纹扩展速率不再有显著变化。进一步对表面裂纹试样进行疲劳裂纹扩展试验，并用勾线法纪录裂纹扩展情况，利用穿透裂纹的da/dN-ΔK曲线预测表面裂纹扩展，用2mm厚试样的数据控制裂纹表面长度的扩展，用14mm厚试样的数据控制裂纹底部沿厚度方面的扩展，得到了与表面裂纹扩展实验吻合很好的预测结果。     

布里奇曼法生长碲镉汞晶体的固液界面形态研究

文中综述了布里奇曼法及加速坩埚旋转技术的布里奇曼法生工碲镉汞晶体过程中固液界面形态的研究结果，简单讨论了固液界面形态对组分分布的影响，并将两种技术所得的组分分布结果进行了比较，在分析影响固液界面形态因素的基础上，认为加速坩埚旋转技术是目前改善固液界面形态的有效方法。     

F级高云母含量云母带的研制及应用

本文介绍了一种F级高云母含量云母带，它的主要特点是云母含量高达48％以上，具有良好的长时间耐电热老化性能，适用于高压电机主绝缘多胶模压工艺要求，该云母带的应用对提高电机绝缘水平和延长电机使用寿命具有重要意义。     

室外LED显示及其在交通领域的应用

介绍了室外LED显示技术及其在道路交通信息显示领域中的应用,指出目前国内室外LED显示屏普遍存在的主要问题.结合应用于高速公路收费站的LED显示屏的设计,给出解决或者克服这些问题的方法.介绍了室外LED显示的现状,预测了其发展趋势.     

Design consideration of photocatalytic oxidation reactors using TiO2-coated foam nickels for degrading indoor gaseous formaldehyde

In the design process of the photocatalytic oxidation (PCO) reactor using TiO₂-coated foam nickels, the optimum of catalyst film thickness, light intensity and flow velocity were considered. A model was developed to study the effect of catalyst film thickness on photocatalytic degradation of formaldehyde by a TiO₂-coated foam nickel at continuous flow mode. In this model, external mass transfer and internal molecule diffusion-reaction were considered. A first-order kinetics equation was used to account for the photocatalytic reaction. Two exponential equations were employed to describe the distribution of light intensities in foam nickels and catalyst films, respectively. Validated with experimental data, the model can be used to predict the optimal thickness of catalyst films. A method for determining appropriate light intensities was proposed and discussed. The appropriate light intensity can be obtained by giving a margin, regarded as an excess coefficient, to the light intensity calculated based on the assumption of complete use of excited electron–hole pairs. The excess coefficient needs to be determined experimentally. In addition, the optimal flow velocity of PCO reactors could be consistent with the required one by changing the windward area of foam nickels. Based on the theoretical analyses, a novel PCO reactor containing 15 parallel-connected cells was designed. Each reaction cell was composed of an UV lamp and a TiO₂-coated tubular foam nickel. The performance of the reactor was tested by degrading gaseous formaldehyde at an indoor concentration level. The results showed that the reactor had low pressure loss and good degradation capability.     

Preparation of submicrometer-sized titania hollow spheres by templating sulfonated polystyrene latex particles

Submicrometer-sized titania hollow spheres with tunable shell thickness and smooth surfaces have been successfully synthesized by employing sulfonated polystyrene (PS) latex particles as a template in sol-gel method. The structure of the particles was characterized by scanning electron microscopy and transmission electron microscopy. The shell thickness was readily tuned by altering the concentration of titanium tetrabutoxide (TBOT) in ethanol solutions. The surface roughness as well as the shell thickness has the tendency to increase with the increase in the concentration of TBOT. The diameter of the hollow spheres was on the average of 20-26% smaller than the diameter of template PS latex particles. Some titania fragments were also observed for the sample with the highest TBOT concentration.     

主电机轴瓦异常情况分析解决办法

介绍南钢中板厂四辊轧机主电机轴瓦一种非典型故障现象，原因分析及解决办法，提出了对类似问题个人见解。     

Powder Deposition in Three Parallel-Oriented Dies of Different Shapes

Uniformity of bulk density distribution during the die filling process is required to minimize quality problems, such as distortion and cracking, for powder compacts. Understanding the die filling process is necessary in ensuring a uniform powder deposition. The second-generation pressure deposition tester (PDT-II) was used to investigate the deposition process and final pressure distribution of powder filling in toroidal, cylindrical, and E-shaped dies. All tests were conducted using a spray-dried free-flowing granular powder. The results indicated that for toroidal dies: (1) the area around 0° orientation (the leeward end) had the highest pressure values (1186.7 to 2498.0 Pa), with the average pressure values of the remaining area 353.7-648.0 Pa; (2) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; (3) the highest feed shoe speed (500 mm/s) led to the most nonuniform pressure distribution among the three speeds; (4) higher feed shoe speed did not always result in higher final pressure values; and (5) the right die tended to have higher final pressure values (215.0 to 2498.0 Pa) than the center die (95.4 to 2052.5 Pa). For E-shaped dies: (1) the final pressure values of the middle leg (308.9 to 760.7 Pa) were higher than those of the left and the right legs (148.9 to 530.3 Pa); (2) the area along the backside had the highest final pressure value (1054.6 to 1303.8 Pa); (3) the pressure distribution was symmetrical about the centerline parallel to the feed shoe movement direction; and (4) neither the center die nor the right die always had higher pressure values than the other one at all locations. Comparison between cylindrical and toroidal dies indicated that: (1) neither of the two die shapes (cylinder and toroid) led to consistently higher or lower final pressure values at all locations and (2) for all three feed shoe speeds, the toroidal die had higher average final pressure values in the 0° orientation.