ON THE COMPOSITION UNIFORMITY AND SHAPE COEFFICIENT OF MOLTEN POOL BY LASER ALLOYING

The effect of the laser processing parameters on the composition uniformity and shapecoefficient of fusion zone with laser surface alloyed Cr plated on medium carbon low alloysteel has been studied.It was found that the composition uniformity depends on the shapecoefficient of fusion zone,and the later is a function of both power density and interactiontime.If the power density is fixed to a certain value,the shape coefficient is directly,propor-tional to the interaction time.A completely,uniform molten pool can be obtained,when theshape coefficient is between 1.6 and 3.0.     

Ф400mm自动轧管机有限元模拟及工艺优化

为提高包钢钢联股份有限公司Ф400mm自动轧管机轧制的钢管壁厚精度．进行了轧卡试验及有限元模拟分析，获得了钢管在孔型中的应变分布状况，经过优化孔型参数和改进轧辊孔型，使轧制的钢管横向和纵向壁厚偏差大大减小。     

激光合金化熔池成分均匀性与形状系数的关系SCIEI

本文研究了激光工艺参数对镀Cr中碳低合金钢激光合金化熔池形状系数及成分均匀性的影响。实验结果表明,熔池成分均匀性取决于其截面形状系数,后者是光束功率密度和交互作用时间的函数。在功率密度一定时,形状系数与交互作用时间成线性关系。当形状系数为1.6—3.0时,可以获得成分均匀的熔池。     

WZ型系列真空铝钎焊炉的研制

简要介绍了WZ型系列真空铝钎焊炉型号，规格等技术参数，并以WZLQH－30型真空铝钎焊炉为例介绍了真空铝钎焊炉的结构及其特点，总结了真空铝钎焊炉设计研究及调试过程中的一些经验体会。     

角接接头焊缝外观检查质量标准的探讨

针对厚壁管角接接头多次出现裂缝,解剖后又没有发现足以引起裂缝的除未焊透外的其它焊接缺陷的情况,认为除应力集中外,角接接头本身的强度也是决定是否会开裂的一个重要原因,为此建立了一个数学模型,同时结合实例证明.按目前大多数人认可的角接接头焊脚的定义,根据DL/T869-2004<火力发电厂焊接技术规程>去控制焊接尺寸,会出现焊缝有效厚度不足的问题.从而根据角接接头有效厚度不应小于最小壁厚的观点,提出对此类角接接头焊缝外观质量控制的几点意见.     

超大型井式气体渗碳炉的研制和应用

对超大型井式渗碳炉设计制造中的难点，如温度均匀性、碳势均匀性、大型炉内结构件的热畸变、炉温及碳势的精确控制等进行了分析，并提出了一系列的技术措施和设计方案。通过试验和生产实践取得了成功，并获得较好的经济效益。     

不等厚板过渡削薄对接焊缝的超声波探伤

不等厚板经过渡削薄处理后的对接焊缝,由于厚度的不均匀,射线穿透时的衰减不一样,对射线检测带来很大的麻烦。常用的超声波探伤方法在定位和定级方面比较困难,本文给出利用现在先进的数字式超声波探伤仪进行准确探伤的方法。     

Experimental Investigation of Epoxy Bonded Polymethylmethacrylate Joints

This paper presents an experimental investigation into various aspects of epoxy-bonded polymethylmethacrylate (PMMA) and PMMA-to-aluminium joints. The effects of adhesive thickness, overlap area, surface roughness, and environmental exposure on the joint strength were studied. Results indicated that the joint strength was not directly proportional to the overlap area, while sanding had a positive effect on the joint strength. A negative effect was observed when adhesive thickness was increased. The fatigue behaviour of adhesively-bonded joints under dynamic loading was found to be independent of frequency, for the range of values tested; however, it was dependent on the test temperature with greater reduction in fatigue life observed in PMMA-to-aluminium joints at higher temperature. Empirical equations from which the fatigue life of joints can be predicted were obtained by regression analysis. Intermittent fatigue testing of the joints was also performed. The epoxy adhesive tested proved to be a satisfactory choice for outdoor exposure. The rate of degradation of the adhesive was slow with the adherend itself degrading at a faster rate than the adhesive or the bondline.     

多层水平气流带式干燥机的数学模型

根据干燥传质传热学原理和干燥动力学特性，建立了水平气流带式干燥机干燥过程的数学模型。该模型可以预测干燥机合理的通风道高度、带翻转最佳时间和热风风速等。为优化多层带式干燥机的结构或设计新的水平气流带式干燥机提供了理论依据。     

Analysis of the diffusion layer thickness, equivalent circuit and conductance behaviour for reversible electron transfer processes in linear sweep voltammetry

The parametric dependence of the diffusion layer thickness upon electrode potential and scan rate has been derived for reversible electron transfer processes in linear sweep voltammetry (LSV) using a simple analytical expression for the dimensionless current function. The quantitative variation of the conductance with potential and scan rate has been illustrated and the equivalent circuit pertaining to LSV has been proposed. Several earlier results pertaining to potential step experiments, thin layer voltammetry, surface bound LSV, radial flow at micro-ring electrodes, etc. are shown to arise from the general expression for the current function obtained here, thus indicating an isomorphism among various potential perturbation techniques.