浅谈东深供水改造工程的设计监理工作

施工图阶段设计监理工作的内容归纳起来主要是对设计质量进行控制.依据<水利建设工程招标、施工图阶段设计监理试行规定>,其具体工作内容仅限于设计成果的合法性和安全性,没有充分发挥设计监理作用,对施工图阶段设计质量的理解是不全面的.施工图阶段的设计质量不仅仅是提交合法和安全的图纸,而且图纸的提交时限性、可实施性及经济性也应是考核设计质量的重要组成部分,为此东深供水改造工程的设计监理工作内容确定为"五项控制"和"两项权利",全面地对施工图阶段的设计质量进行控制.     

连续小波变换在函数空间中的应用

某些微分方程和相应的积分方程之间的关系被讨论；这些微分方程通过边境小波变换可被转换成相应的积分方程，它们不仅在弱收敛意义下而且在范围数收敛意义下是等价的；关于这些微分方程的讨论就与相应的积分方程的讨论联系起来。     

纳米ZrO2等离子涂层的结构,性能和工艺特点

采用大气等离子喷涂技术(APS)，制备了常规氧化锆和纳米结构氧化锆两种涂层．利用扫描电镜(SEM)对涂层的显微结构进行了观察．对两种涂层的沉积效率、表面粗糙度和显微硬度作了对比研究．结果表明，粉末原料的显微结构、粒度、形态、喷涂工艺参数(喷涂功率和距离)对涂层的显微结构有较大的影响．等离子喷涂造粒纳米氧化锆粉制备的涂层沉积效率高而稳定，其显微结构与喷涂功率和距离密切相关．与常规氧化锆涂层相比，纳米结构氧化锆涂层具有较高的显微硬度和较低的表面粗糙度．     

光折变三维信息存储器

分析光折变三维存储器的机理,探讨了光折变三维存储器的编码方式、光折变材料的选择及存储技术,阐述了其产业化进程.     

伶仃洋三维潮流输沙的数值模拟

作者使用垂向坐标变换技术，结合有限差分方法建立了三维潮流输沙的数学模型。为了增加模型的稳定性和减少数值耗散，对悬沙对流扩散方程中的水平对流项采用三阶迎风格式离散。应用本模型对伶仃洋的枯季和洪季的潮流输沙的悬沙场进行了数值模拟，将模拟结果与实测资料进行比较，二者吻合较好。模拟结果分析表明：伶仃洋悬沙运动主要集中在西滩，对伶仃航道影响不大；洪季水体含沙浓度高于枯季；水体含沙浓度沿水深存在浓度梯度，且洪季的浓度梯度明显大于枯季。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

用于高频谐振器的PbTiO_3基压电陶瓷

传统的PZT压电陶瓷的相对介电常数较大,一般为1 000以上,用于高频谐振器不易与线路匹配;而PbTiO3基压电陶瓷的相对介电常数较小,一般仅为200左右,对于10 MHz以上频率的谐振器,用PbTiO3基压电陶瓷作为压电振子是最佳的选择。本文主要研究用于高频谐振器的MnO2和Nd2O3改性PbTiO3基压电陶瓷的性质。PbTiO3基压电陶瓷的性质的改善是与此种陶瓷的制备工艺,显微结构和电导机制紧密相关的。     

Microstructure of Feta Cheese Made Using Different Cultures as Determined by Confocal Scanning Laser Microscopy

ABSTRACT: The objective of this work was to observe the microstructure of feta cheese using confocal scanning laser microscopy. Low fat cheese and cheese containing capsule-producing cultures were made. The protein network was observed using the reflectance mode of the confocal microscope. Fat was stained by Nile red dye diluted with whey. More even distribution of fat with a larger number of smaller globules was observed in cheese made with noncapsule-forming culture compared to that made with the capsule-forming culture. Nonfat cheese had compact structure when made with noncapsule-forming culture which contrasted with the open structure observed in cheese made with the capsule-forming culture     

模拟信号的恢复及其误差研究

数模混合仿真中模拟信号的恢复及其误差对整个仿真过程具有重要影响。本文探讨了用零阶保持和一阶保持进行信号恢复的方法，比较了它们的误差及工作特点。特别指出了一阶保持中，由于存在积分器复原时间及数字机操作时间的影响而会带来附加的误差，因此一阶保持方法较难达到其理论的精度。