疲劳裂纹扩展行为的研究现状及钛合金的疲劳裂纹扩展特征

疲劳裂纹扩展行为是现代材料研究中重要的内容之一。论述了组织结构、环境温度、腐蚀条件以及载荷应力比、频率变化对材料疲劳裂纹扩展行为的影响。总结出疲劳裂纹扩展研究的常用方法和理论模型,并讨论了"塑性钝化模型"和"裂纹闭合效应"与实际观察结果存在的矛盾。最后,对钛合金疲劳裂纹扩展研究的内容和研究结果进行了概述。     

Microstructure of Titanium after Hydrogenation

ＭｉｃｒｏｓｔｒｕｃｔｕｒｅｏｆＴｉｔａｎｉｕｍａｆｔｅｒＨｙｄｒｏｇｅｎａｔｉｏｎＷａｎｇＹｕ；ＷａｎｇＰｅｉｘｕａｎ；ＺｈａｎｇＪｉａｎｗｅｉ（王宇）（王佩璇）（张建伟）ＵｎｉｖｅｒｓｉｔｙｏｆＳｃｉｅｎｃｅａｎｄＴｅｃｈｎｏｌｏｇｙＢｅｉｊｉｎ...     

改善Fe-B-C合金韧性的研究

为了提高Fe-B-C合金的韧性,应用稀土-钛-氮复合变质剂改善Fe-B-C合金组织和性能。结果发现,Fe-B-C合金复合变质处理后的凝固组织明显细化,且组织分布均匀,并出现钛硼化合物,钛硼化合物不同于普通Fe-B-C合金中的Fe2B呈网状分布,而是呈断网状和块状分布,特别是经高温热处理后,硼化物变成球状和棒状,Fe-B-C合金韧性明显提高,由8～10 J/cm2提高至22～25 J/cm2。经变质处理的Fe-B-C合金可用于制造轧钢机导卫板,其耐磨性比高镍铬合金钢提高1.3倍。     

Microstructural evolution and interfacial reactions between Ti and ZrO2/CaTiO3 composites

Various proportions of ZrO₂/CaTiO₃ powders were mixed and hot pressed at 1500°C/30 min for Ti casting. The hot-pressed ZrO₂/CaTiO₃ composites were reacted with pure Ti at 1700°C/10 min in Ar. The interfacial reaction between Ti and ZrO₂/CaTiO₃ composites was investigated through X-ray diffraction, scanning electron microscopy, transmission electron microscopy, and energy-dispersive X-ray spectroscopy. The ZrO₂/CaTiO₃ composites with less than 10 vol.%, CaTiO₃, and a minor amount of residual TiO₂ were found. When the content of ZrO₂ was increased to larger than 10 vol.%, two Ca₂Zr₅Ti₂O₁₆ and CaZrTi₂O₇ phases appeared in the composites. The amount of CaTiO₃ and CaZrTi₂O₇ in the composites gradually decreased as the amount of ZrO₂ increased. When Ti came in contact with ZrO₂/CaTiO₃ composites with less than 10 vol.% ZrO₂, the resulting eutectic reaction produced a liquid phase and induced melting. When ZrO₂ was increased to more than 30 vol.% in the composites, Ca₂Zr₅Ti₂O₁₆ and CaZrTi₂O₇ changed completely to CaZrO₃, Ti₂O, CaO, and ZrO₂. With more than 30 vol.% ZrO₂, no other reaction phases occurred in the Ti side after contact with the ZrO₂/CaTiO₃ composites, which is conducive for producing ceramic composites for Ti casting applications.     

Johnson-Cook dynamic constitutive relationship for TC 16 titanium alloy

The true stress--strain curves of TC16 alloy with a wide range of strain rates were investigated under uniaxial quasi-static tension and uniaxial dynamic compression with the lnstron 8032 test machine and the split Hopkinson bar respectively. The results indicate that the true stress increases with increasing strain rate, while decreases with increasing temperature. Under the 105 s^-1 high strain rate and temperature higher than 673 K, the true stress would even be less than that under quasi-static condition. A new method incorporating TCl6＇s stress strain curve developing item was proposed to determine the coefficients in J-C model easily and to avoid the estimation of the adiabatic temperature rising. The Johnson-Cook dynamic constitutive relationship for TC16 was obtained for the first time. Good agreement was obtained between the model prediction and the experimental stress--strain curves for TC16 under both quasi-static and dynamic loadings.     

The effect of α phase on the deformation mechanisms of β titanium alloys

The effects of α and β phase interactions on the tensile and creep deformation behavior of β titanium alloys was studied using Ti-6.0wt.% Mn and Ti-8.1wt.%V as the model two-phase alloys, and Ti-13.0wt.%Mn and Ti-14.8wt.%V as the single-phase β alloys. The β phase of α-βTi-8.1V deforms by stress-induced hexagonal martensite (α′), while slip and twinning occurs in the single-phase β alloy with the same chemistry as the β phase. No stress-induced martensite was observed in the β or α-βTi-Mn alloys. This behavior is modeled in terms of a number of factors, including elastic interaction stresses between the α and β phases, coherency between the α phase and hexagonal martensite, and β phase stability. This paper was presented at the Beta Titanium Alloys of the 00’s Symposium sponsored by the Titanium Committee of TMS, held during the 2005 TMS Annual Meeting & Exhibition, February 13–16, 2005 in San Francisco, CA.     

钛及钛合金抑菌技术的研究进展

钛作为食品接触材料不具备抑菌功能,使用过程中易滋生细菌对人体健康不利。文章主要介绍了钛及钛合金抑菌处理常用方法及最新的研究进展,包括合金化处理,离子注入、热喷涂、微弧氧化等表面处理方式。对抑菌钛合金的研究方向及其在日用餐具、炊具、水具等行业的应用前景作了展望。     

氢处理技术在钛合金中的应用

氢处理工艺是钛合金的一种特有的热处理方式，用于改善铸造、锻造钛合金件以及粉末冶金件的组织和性能。本文综述了氢处理在钛合金中的一些应用，主要介绍了国外的研究动向。     

淬火温度对铸造Fe—B—Ti合金组织和性能的影响

通过不同的热处理淬火温度改变铸造Fe—B—Ti合金的组织，探讨了铸造Fe—B—Ti合金不同组织与性能的关系。试验结果表明：淬火温度较低时，硼化物变化较小，网状分布趋势明显；淬火温度较高时，硼化物断网和团聚化趋势明显加快。淬火温度1050℃时，硼化物网状特征消失，基本上都变成了团块状、颗粒状和杆棒状分布。随着淬火温度升高，硬度和韧性增加，超过1000℃，硬度和韧性变化不明显。淬火温度1050℃时，综合性能良好。     

热处理对Ti-Al-Sn-Zr-Mo-Si-X系合金性能的影响

研究了热处理对3种Ti-Al-Sn-zr-Mo-Si-X（X为ⅤB，ⅥB族一种或几种元素）系合金（A、B、C）室温拉伸性能的影响，对优化合金的热处理制度及优选热处理制度下3种合金的疲劳裂纹扩展行为也进行了探讨。结果表明，优选热处理制度下A、C合金的裂纹扩展速率差别不大，B合金560℃时效处理后，裂纹扩展速率比540℃时效处理的小。在相同热处理制度下，比较3种合金裂纹扩展速率的结果表明，IgΔK在1．2～1．5范围内B合金的抗疲劳裂纹扩展性能较优。