A comparison of transformation methods for evaluating two‐dimensional weakly singular integrals

Accurate numerical evaluation of integrals arising in the boundary element method is fundamental to achieving useful results via this solution technique. In this paper, a number of techniques are considered to evaluate the weakly singular integrals which arise in the solution of Laplace's equation in three dimensions and Poisson's equation in two dimensions. Both are two‐dimensional weakly singular integrals and are evaluated using (in a product fashion) methods which have recently been used for evaluating one‐dimensional weakly singular integrals arising in the boundary element method. The methods used are based on various polynomial transformations of conventional Gaussian quadrature points where the transformation polynomial has zero Jacobian at the singular point. Methods which split the region of integration into sub‐regions are considered as well as non‐splitting methods. In particular, the newly introduced and highly accurate generalized composite subtraction of singularity and non‐linear transformation approach (GSSNT) is applied to various two‐dimensional weakly singular integrals. A study of the different methods reveals complex relationships between transformation orders, position of the singular point, integration kernel and basis function. It is concluded that the GSSNT method gives the best overall results for the two‐dimensional weakly singular integrals studied. Copyright © 2002 John Wiley & Sons, Ltd.     

2.4GHz动态CMOS分频器的设计

对现阶段的主流高速CMOS分频器进行分析和比较,在此基础上设计一种采用TSPC(truesingle phase clock)和E-TSPC(extended TSPC)技术的前置双模分频器电路.该分频器大大提高了工作频率,采用0.6μm CMOS工艺参数进行仿真的结果表明,在5V电源电压下,最高频率达到3GHz,功耗仅为8mW.     

Defocusing image to pattern contact holes using attenuated phase shift masks

The patterning of contact holes by selecting out-of-focus image plane (defocus) using attenuated phase shift masks (APSM) has been studied. Defocus is found to enhance the image modulation at low partial coherence for contact holes with negative local average of mask function. Semi-dense holes up to 130 nm in 8% APSM have been printed by 0.5 μm defocus at a partial coherence of 0.31 using KrF scanner with highest numerical aperture of 0.68. However, these holes were closed with in-focus imaging. Defocus is also found to be beneficial for patterning the pitches that have extensive side lobes with in-focus imaging.     

Monte Carlo simulation of gas phase polymerization of 1,3‐butadiene. Part II: Kinetics optimization and confirmation

Studies on the deactivations and initiations of gas phase polymerizations of 1,3‐butadiene have been achieved by Monte Carlo simulation. Initiation and deactivation control the reaction before and after the peak of the polymerization rate, respectively. The influence of polymerization temperature has been studied. Monte Carlo modeling of polymerization kinetics and mechanism was confirmed by the agreement of experimental data and simulation results of polymerizations run with a temporary evacuation of monomer. The balance of catalysts and active chains is established by both initiation and chain transfer reactions with cocatalyst, which causes a ‘pseudo‐stability’ stage. © 2003 Society of Chemical Industry     

连续波雷达测距中的解模糊技术

研究连续波雷达测距中的距离模糊问题，分析几种常用解模糊方法的性能，并讨论参差比的选取对测距范围的影响。     

地震数据采集系统延迟时间研究与分析

文章分析了影响地震采集系统延迟时间的因素,并根据系统延迟的理论对产生的原因进行了论证.同时对实际生产中的测试方法进行了阐述研究和分析,提出了新的测试方法,并结合实际生产提出了合理性建议.     

双频抽运提高SBS相位共轭保真度

相位共轭保真度是相位共轭镜技术用于强激光系统中的一个重要指标。采用四波混频加强SBS的方法 ,其相干拍频驱动声子场 ,能提高SBS相位共轭保真度。对于双频单池结构 ,使用列阵相机测量激光束能量远场角分布 ,在SBS转换效率最佳时 ,对相干驱动SBS相位共轭保真度进行了实验研究     

机械合金化Fe-Ni粉末的相结构

使用XRD和Moessbauer等方法，研究了在Ar气氛下机械合金化Fe—Ni粉末相结构的变化．结果表明，在机械合金化Fe64-Ni36粉末过程中，fcc相的数量随着球磨时间的增加先增加然后减少，与加乙醇球磨Fe64-Ni36的情形相同．当Ni的含量(原子分数)大于50％时，有fcc相、顺磁相和FeNi3形成，当Ni的含量低于50％时，bcc相的数量随着Ni含量减少而增加．Moessbauer谱的结果表明，因球磨时间或Fe、Ni比例的不同，Fe—Ni球磨粉末固溶体具有不同结构的原子配比。     

带通采样在数据采集中的应用研究

在数据采集中采用带通采样，可大大降低采样率，但系统中的抗混叠滤波器会造成相位的非线性。采用对滤波后的信号进行带通采样，然后再用FRR滤波器校正相位的非线性，从而不失真地还原原信号，最后在Matlab中进行仿真，验证了该方法的有效性。     

Phase behavior,density, and crystallization of polyethylene in n‐pentane and in n‐pentane/CO2 at high pressures

The phase behavior and volumetric properties of polyethylene (PE) in solutions of n‐pentane and n‐pentane/CO₂ were studied in a temperature (T) range of 370–440 K at pressures up to 60 MPa. Measurements were conducted with a variable‐volume view‐cell system equipped with optical sensors to monitor the changes in the transmitted light intensity as the P or the T of the system was changed. Lower‐critical‐solution‐temperature‐type behavior was observed for all of the liquid–liquid (L–L) phase boundaries, which shifted to higher pressures in solutions containing CO₂. The solid–fluid (S–F) phase boundaries were investigated over a P range of 8–54 MPa and took place in a narrow T range, from 374 to 378 K in this P interval. The S–F phase boundary showed a unique feature in that the demixing temperatures showed both increasing and decreasing trends with P depending on the P range. This was observed in both the PE/n‐pentane and PE/n‐pentane/CO₂ mixtures. The density of these solutions were measured as a function of P at selected temperatures or as a function of T at selected pressures that corresponded to the paths followed in approaching the phase boundaries (S–F or L–L) starting from a homogeneous one‐phase condition. The data showed a smooth variation of the overall mixture density along these paths. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2201–2209, 2003