Effects of apitong (Dipterocarpus spp.) extractives on bond strength development and curing rate of adhesives

Emulsion polymer isocyanate ( ), polyvinyl acetate ( ) and resorcinol-formaldehyde ( ) adhesives were used to produce single lap shear specimens using resinous and non-resinous apitong (Dipterocarpus spp.) timbers. Tests showed that joints made with highly resinous apitong were about 40% weaker than similar joints made with non-resinous apitong. The resinous apitong was treated with different solvents to yield five different extractives which were characterized by infra-red analysis. Apitong extractives were then added to and adhesives and joints made with buna (Fagus crenata), a timber known to be low in extractives and easy to bond. Joints prepared using extractive-containing adhesives were generally weaker than those made with the unmodified adhesives. RF adhesives containing extractives cured more slowly than unmodified . It is thought that the acidic nature of the extractives changes the pH of the system sufficiently to affect the curing mechanism     

Rheology of cementitious paste with silica fume or limestone

The rheological behaviour of cementitious pastes where cement has increasingly been replaced by densified silica fume (SF), untreated SF or limestone has been studied. The effect of SF on the flow resistance, taken as the area under the flow curve, was found to depend on the dispersing ability of the plasticizer as illustrated by pastes with naphtalene sulphonate-formaldehyde condensate (SNF) and polyether grafted polyacrylate (PA).The gel strengths increased with increasing SF replacement of cement independently of plasticizer type. The cementitious gel strength was, however, depending on the type of SF since pastes with densified SF developed lower gel strengths than pastes with untreated SF. This phenomenon was attributed to agglomerates in the densified SF which remained unbroken by the mixing and measurement sequence.Both flow resistance and gel strength decreased with increasing limestone replacement. Thus, silica fume may have an advantage over limestone filler as stabilizing agent for self-compacting concrete preventing segregation upon standing and reduced form pressure due to a more rapid gel formation.     

Effect of fretting amplitudes on fretting wear behavior of steel wires in coal mines

Given that fretting wear causes failure in steel wires, we carried out tangential fretting wear tests of steel wires on a self-made fretting wear test rig under contact loads of 9 and 29 N and fretting amplitudes ranging from 5 to 180 μm. We observed morphologies of fretted steel wire surfaces on an S-3000N scanning electron microscope in order to analyze fretting wear mecha-nisms. The results show that the fretting regime of steel wires transforms from partial slip regime into mixed fretting regime and gross slip regime with an increase in fretting amplitudes under a given contact load. In partial slip regime, the friction coefficient has a relatively low value. Four stages can be defined in mixed fretting and gross slip regimes. The fretting wear of steel wires in-creases obviously with increases in fretting amplitudes. Fretting scars present a typical morphology of annularity, showing slight damage in partial slip regime. However, wear clearly increases in mixed fretting regime where wear mechanism is a combination of plastic deformation, abrasive wear and oxidative wear. In gross slip regime, more severe degradation is present than in the other regimes. The main fretting wear mechanisms of steel wires are abrasive wear, surface fatigue and friction oxidation.     

GCr15轴承钢连铸过程中热物性参数的研究

借鉴前人实验数据,采用一定的数学方法,对轴承钢的热物性参数进行了研究.结果表明：GCr15轴承钢的液相线温度为1 465.7℃,固相线温度为1 328.4℃,零强度温度为1 380℃左右,零塑性温度为1 330℃左右;在固相区、液固两相区、液相区分别采用不同的公式进行处理,可使结果更加准确,还避免了奇异性.研究结果可为轴承钢连铸工艺有限元模拟提供基础.     

型钢翼缘狗骨式削弱在型钢混凝土节点的作用

为了防止地震时型钢混凝土节点核心区发生剪切破坏以及梁柱连接焊缝发生脆性断裂,提出对型钢混凝土节点核心区附近梁端型钢的上、下翼缘采取狗骨式削弱,并系统研究翼缘削弱对提高型钢混凝土节点抗震性能的作用.研究表明,由于在梁端型钢翼缘采取狗骨式削弱,不仅能够将塑性铰控制在梁型钢削弱的位置,从而有效地降低了节点核心区所受的剪力以及梁柱连接焊缝的应力;而且能够改善节点塑性铰区的转动能力和抗剪性能,提高节点的延性和耗能能力.     

改善钢桥面铺装层高温作用的有效措施

为了降低钢桥面铺装层内较高的温度,提高铺装材料使用性能,推迟桥面的早期破坏.采用有限元手段,以傅里叶传热定律为理论基础,根据气象部门提供的气象资料,对开放式钢箱梁及封闭式钢箱梁铺装层的温度场进行研究.结果表明:开放式箱梁可以降低桥面铺装层温度,降低高温持续作用时间,改变桥面铺装层高温的作用位置.     

树脂增强选择性激光烧结多孔金属件的研究

针对选择性激光烧结(SLS)间接方法成型的金属零件形坯,经脱脂和高温烧结后形成的零件存在大量孔隙和空洞,其致密度和强度都较低,不能满足实际应用要求的问题,采用改性耐高温环氧树脂浸渗零件烧结坯的方法,使多孔金属件致密化,并粘结内部金属网架,提高零件的机械性能.对浸渗烧结坯的拉伸强度的测试和扫描电镜(SEM)以及热失重(TGA)的分析结果表明,浸渗树脂后的烧结坯拉伸强度提高了约4倍;改性环氧树脂和金属网架粘结在一起,形成一个密实的网络结构,致密度大幅提高;零件可在200℃的温度下使用.该方法可以制造注塑模具和功能零件.     

新型钢铅组合耗能器性能试验及参数优选

为了考察新型钢铅组合耗能器(NCSLD)的力学性能和提高其耗能能力,利用电液伺服压剪试验机对NCSLD耗能器进行力学性能试验,采用ANSYS实体建模的方法对耗能器进行大量的数值分析,并对性能试验和数值分析的结果进行对比,研究耗能器的滞回特征参数与其6个几何参数之间的关系,回归出二者之间的公式.提出评价耗能器性能优劣的标准及其附加条件,并以此标准为依据,利用均匀设计法和遗传算法分别对耗能器的6个几何参数进行优选.结果表明遗传算法的选优效果要好于均匀设计法,同时得到一系列性能良好的NCSLD耗能器.     

Zonal disintegration phenomenon in enclosing rock mass surrounding deep tunnels -- Elasto-plastic analysis of stress field of enclosing rock mass

The zonal disintegration phenomenon (ZDP) is a typical phenomenon in deep block rock masses. In order to investigate the mechanism of ZDP, an improved non-linear Hock-Brown strength criterion and a bi-linear constitutive model of rock mass were used to analyze the elasto-plastic stress field of the enclosing rock mass around a deep round tunnel. The radius of the plastic region and stress of the enclosing rock mass were obtained by introducing dimensionless parameters of radial distance. The results show that tunneling in deep rock mass causes a maximum stress zone to appear in the vicinity of the boundary of the elastic and the plas-tic zone in the surrounding rock mass. Under the compression of a large tangential force and a small radial force, the rock mass in the maximum stress zone was in an approximate uniaxial loading state, which could lead to a split failure in the rock mass.     

考虑初始弯曲矩形薄壁钢管砼柱管壁屈曲分析

实际工程中的钢管都是有初始弯曲的,初始弯曲的存在会降低薄壁钢管混凝土柱的承载力.采用能量法对具有初始弯曲管壁的屈曲性能进行了分析,分析结果表明,初始弯曲的存在会使管壁的宽厚比降低30%左右.