复合材料空心飞轮多环套装整体变形及应力简化精细分析

采用多环过盈装配是解决复合材料飞轮径向强度过低的有效途径之一。本文作者采用平面应力简化模型,提出了计及过盈配合后变形导致实际过盈量增大计算飞轮套装后的初终应力分布的方法;提出了基于叠加原理计算多环过盈装配旋转飞轮应力的方法;提出了保证飞轮旋转时配合界面不脱离的相关临界转速的概念和计算方法。算例分析表明:过盈配合后的变形对初终应力的影响不能忽略;过盈量和套装环数与飞轮的初终应力和相关临界转速有密切的关系。     

堆石料与基岩面直剪试验

介绍了堆石料与基岩面的现场直剪试验方法，6个组次的直剪试验结果表明，堆石料与基岩面的抗剪强度指标随基岩面坚硬度的增大而增加，并随基岩面粗糙度的加大而加大。     

Micro assembly injection moulding

Injection moulding is established as one of the most common manufacturing processes of thermoplastics due to its high degree of automation and the short cycle times. Micro injection moulding is a rapidly growing technology that allows for the efficient production of very complex micro parts in high series. The “Market Analysis for Microsystems II 2002–2005” of the Nexus Task Force anticipates a yearly growth in the field of micro system technology of about 20% (Wechsung et al. 2002). This study identifies in addition to the continuous miniaturization the growing use of polymers in micro systems (Schneider et al. 2001). No other material group offers this wide range of material properties and permits to choose processing parameters and application properties according to necessities (Gächter 2000). While the production processes of micro technical components are mainly controllable, the assembly of these components to hybrid micro systems is a bottleneck to the industrial large scale production. The assembly itself represents a large fraction of the added product value and gains in importance with growing complexity and miniaturization of the systems.     

魏氏组织对20#碳钢H2S应力腐蚀开裂性能的影响

文章对H₂S-CO₂-H₂O腐蚀环境下发生H₂S应力腐蚀的20^＃碳钢弯管（无缝钢管）进行了成分、组织、拉伸、硬度和应力腐蚀开裂等性能的试验研究，并与同材质、同时投产、腐蚀环境基本相似而未发生应力腐蚀开裂的在役弯管及未使用的新弯管作对比，结果表明魏氏组织是引起20^＃钢发生应力腐蚀开裂的主要原因；正火能消除魏氏组织，降低钢的应力腐蚀开裂敏感性。     

Effects of diacrylate monomers on the bond strength of polymer concrete to wet substrates

The bond strengths of polymer concretes containing up to 15% (based on polymer resin) of diacrylate (DA) monomers were examined and compared with those without DA. A change occurring with the addition of DA monomers was an increase in the bond strength of polymer concrete to wet substrates. Zinc diacrylate (ZDA) and calcium diacrylate (CDA) were each used as an additive to monomers and resins [methyl methacrylate (MMA), polyester, and two kinds of epoxies]. The variables were amount of the DA monomers and surface conditions (wet or dry and smooth or rough). Bond strengths were measured by tension bond. ZDA was found to improve the bond strength of MMA and polyester, whereas CDA improved the bond strength of epoxies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 991–1000, 2003     

An investigation into the effect of various chemical and physical treatments of a South African phosphogypsum to render it suitable as a set retarder for cement

The work describes various physical and chemical treatments to eliminate the deleterious effects of impurities in phosphogypsum on the delayed setting time and impaired strength development behaviour of cement to which it was added as a set regulator. The physical treatments included washing, milling, and ultrasonic treatment of the material, while the chemical treatments dealt with acidic and basic additions to the phosphogypsum during the washing stage. It was found that chemical treatment with a milk of lime solution, which is often recommended in literature, was ineffective in reducing set retardation. Treatment with ammonium hydroxide or sulphuric acid was more effective in this regard. Intergrinding phosphogypsum with slaked lime improved its effectiveness in reducing set retardation, but the use of unslaked lime was less effective and also resulted in marked reductions in compressive strengths. A combined treatment of wet milling phosphogypsum with a lime slurry in a ball mall was derived from these experiments and is recommended for full-scale plant applications.     

珠光体球化的分形研究

珠光体球化反映到金相上，是一种不规则图像的变化，并且具有分形的特征，可望用分形几何的方法来进行描述。以Cr-Mo钢的珠光体球化为例，用分形维数来描述珠光体球化程度；用小岛法对15CrMo钢的珠光体球化图谱进行了测量。实验表明，珠光体球化从1级到6级，其相应的分形维数范围为1.3156-1.9282。从电厂运行了10^5h的15CrMo钢管上取样，实测了该试样的珠光体球化等级，结果表明，以分形维数表示的球化程度与按图谱评定的球化等级完全吻合。     

热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

滚动式冷床在高钢级油管生产线中的应用

根据石油开采业对石油机械产品的需求 ,利用机械理论基础知识 ,通过实践设计 ,提出了对几何尺寸长的金属管类进行调质处理后的均匀冷却方法 ,以满足其性能要求。     

δ－Al_2O_3纤维／Al－12Si复合材料室温拉伸强度分析

对δ－Ａｌ２Ｏ３纤维／Ａｌ－１２Ｓｉ复合材料室温拉伸强度的分析表明，在实验条件下该复合材料存在δ－Ａｌ２Ｏ３纤维的最小体积分数Ｖｍｉｎ和临界体积分数Ｖｃｒｉｔ，并求出其基体强度σ＇ｍ和室温强度σｃ－δ－Ａｌ２Ｏ３纤维体积分数Ｖｆ直线方程及纤维的临界长度ｌｃ和复合材料的剪切应力τｉ．确定复合材料的ＲＯＭ预测曲线，应首先判断σ＇ｍ是否等于未增强合金的强度σｕｍ才能得出正确的结论