基于激光多普勒测速法的2×106m/s2高冲击校准技术

在高冲击传感器动态性能校准中,实现高量程、宽脉冲激励是目前高冲击校准急需解决的问题。采用速度改变法校准原理,以气炮为激励源,利用激光多普勒测速方法测量砧体运动速度,建立高冲击校准系统。分析碰撞系统的作用原理,提出调整和控制激励脉宽的方法;分析测速误差,提出双光束差动侧向测速方法。实验结果表明:高冲击校准系统校准量程为2×106m/s2,激励脉宽在2×106m/s2时大于100μs,校准冲击灵敏度的扩展不确定度小于5%(k=2)。     

基于LabVIEW的超声信号小波阈值去噪方法

图形化编程软件LabVIEW具有强大的信号采集功能,但对于需要进行大量数据运算处理的复杂应用就显得力不从心。数学工具软件MATLAB强大的计算功能及较高的编程效率可以弥补LabVIEW开发的不足。文中结合两者软件的优点,采用混合编程的方法进行实际工程的去噪处理,同时针对超声缺陷回波信号信噪比低、易于被噪声淹没的特点,选取小波阈值去噪的方法,通过调用LabVIEW里的MATLAB Script节点对信号进行仿真实验,仿真结果表明采用stein的无偏风险阈值去噪的方法消噪效果最为明显,得到较高的信噪比。     

自洁式超声波在线过滤器的研制

我国地表水浊度高,极大地影响基于光度法的在线分析仪器正常运行;以自主创新的在线采水过滤头为核心,提出一种新型的自洁式超声波在线过滤器,由超声波电源、采水和反冲洗模块、嵌入式控制模块等组成,具备定时定速过滤采水、超声波反冲清洗等功能;实验结果表明,过滤器能够连续地自动滤除水中的悬浮物质,并且不影响目标物的化学形态,对同一水样的浊度去除率维持在85%左右。     

基于超声波的围岩松动圈实时监测系统设计

实时地掌握围岩松动圈的范围对矿藏的安全生产具有重要的意义。利用超声波探测的灵活性和准确性,本文提出了一种基于超声波的围岩松动圈监测系统设计方法。此方案利用超声波在岩体中的传播速度与岩体的受力状态和裂隙程度的关系来实时地监测围岩松动圈的情况,具有方便、灵活、易于操作等特点。     

减振器的分析与改进方案

本文对几种典型减振器做了一些分析,并根据我国主战坦克的特点提出了一种新的改进设计方案,在文中暂称为“复合作用”式减振器。它既能产生象摩擦减振器的摩擦阻尼,又能具有筒式减振器的小孔节流阻尼效果。两种阻尼的复合作用如调整适当,则对提高悬挂系统对地面情况的变化适应能力,改善车辆行驶平稳性和可靠性有很大的帮助。     

Nondestructive characterization of the mechanical strength of diffusion bonds. II. Application of a quasi-static spring model

It has been shown that the acoustic response of imperfect interfaces may be described by a quasi-static spring model. In the present paper, experimental data on the geometry of the contacts between two diffusion-bonded blocks have been used to determine the spring stiffness of such interfaces which have been correlated with experimentally determined ultrasonic reflection coefficients. The correlation between the theoretical reflection coefficient and the spring stiffness was found to be in excellent agreement with experimentally-observed values, if the disbonds are of infinitesimally small thickness. For disbonds of finite thickness, the agreement is less satisfactory. Reasons for the discrepancy in the latter case are unknown at the present time.     

组合肋板式陶瓷换热器材质的研究

以耐火粘土、高矾土及滑石为原料研制了堇青石基陶瓷材料,并对其组织和性能尤其是抗热震性进行了研究。结果表明,堇青石基上分布着针状莫来石的材料具有更高的抗热震性。对评价换热器用陶瓷材料抗热震性参数进行了讨论,指出抗热震损伤参数R″″更适合于作为优选陶瓷换热器用材质的指标。     

Preparation of micro-arc oxidation coatings on magnesium alloy and its thermal shock resistance property

1. Introduction Due to their high specific strength, good electro-magnetic shielding characteristics, high damping characteristics, good cast ability, and excellent pol-ishing capability, magnesium alloys are extensively used in aeronautical, automobile, and electro- communication industries [1-3]. But magnesium has some disadvantages, such as low chemical stability, high negative electric potential, and low hardness, so it is necessary to use surface disposal to accommo-date the demand for re…     

Ultrasonic-assisted drilling of Inconel 738-LC

Generally in the drilling of modern aviation materials such as nickel and titanium base super alloys, problems frequently occur in terms of burr formation at the cutter exit, tool stress, high heat generation on tool surface as well as low process reliability. A recent and promising method to overcome these technological constraints is the use of ultrasonic assistance, where high-frequency and low-amplitude vibrations are superimposed on the movement of cutting tools. This paper presents the design of an ultrasonically vibrated tool holder and the experimental investigation of ultrasonically assisted drilling of Inconel 738-LC. The circularity, cylindricity, surface roughness and hole oversize of the ultrasonically and conventionally drilled workpieces were measured and compared. The obtained results show that the application of ultrasonic vibration can improve the hole quality considerably. Improvements of up to 60% have been achieved.     

水工混凝土构件裂缝检测方法及应用

水利工程在长期运行过程中,其混凝土构件会出现磨蚀、裂缝等损伤,如这类问题不能够及时得到处理,将会严重影响水利工程的安全运行。本次研究主要针对水工混凝土构件中的裂缝检测方法进行研究,提出从“定性”到“定量”的一体化检测思路,具体实施过程分为四部分,即“普探—详查—判定—验证”,其中,普探阶段采用探地雷达法,确定裂缝的总体分布;详查阶段采用超声横波反射三维成像的方法,确定裂缝的纵深向分布;判定阶段分别采用裂缝测宽法和表面声波法,用来确定裂缝的表面宽度和贯穿深度;验证采用钻孔电视,确定探测结果的正确性和准确性。上述技术路线突破了单一方法的限制,可有效地运用于水工混凝土构件裂缝检测,经实践证实,具有良好的检测效果。