Thermomechanical stress fields in high-temperature fibrous composites. I: Unidirectional laminates

This two-part paper presents a closed-form procedure for evaluation of estimates of local thermomechanical stress fields in two-phase fibrous composites and laminates. The first part is concerned with a unidirectional elastic laminate subjected to uniform mechanical loads and to uniform changes in temperature. Both phases are assumed to be elastic, with temperature-dependent moduli and expansion coefficients; the solution reflects the influence of thermomechanical interactions. Exact solutions are not possible for any real system, because the local geometry is not known in detail. Instead, estimates of the fields are found from a modified Mori-Tanaka approximation. Examples are presented for two SiC/Ti---Al---Nb composites. Local stresses of interest are found after cooling from fabrication to room temperature. The presence of local yielding, and the influence of coupling terms on the local stress magnitudes are examined. Extension of the results to laminated plates is presented in Part II (Dvorak, G.J., Chen, T. & Teply, J., Composites Science and Technology, 43 (1992) 359–368, this issue).     

Synthesis and characterization of poly(siloxane-urethane)s

A series of polyurethane block copolymers based on hydroxy-terminated polydimethylsiloxane and poly(propylene glycol) soft segments of molecular weights 1818 and 2000, respectively, were synthesized. The hard segments consisted of 4,4′-diphenylnethane diisocyanate and 1,4-butanediol as the chain extender. Samples with different molar ratios were prepared. We tried to synthesize polydimethylsiloxane-based polyurethanes (PDMS-PU) containing a hard block as major fraction and a soft block as minor fraction for preparing toughened rigid systems. After a study of the pure polydimethylsiloxane-based polyurethane and poly(propylene glycol)-based polyurethane (PPG-PU), (mixed polyol)-based block copolymers and blends of PDMS-PU and PPG-PU were synthesized, and characterized by means of differential scanning calorimetry, tensile testing and scanning electron microscopy. In (mixed polyol)-based copolymers and lower hard-segment content blends, macro-phase separation occurred, but blends with higher hard-segment contents showed significant reduction in amounts of phase separation.     

Phenol novolac/poly(4- hydroxyphenylmaleimide) blend hardeners for DGEBA-type epoxy resin

Phenol novolac/poly (4-hydroxyphenylmaleimide) (PHPMI) blends were used as an epoxy resin hardener. The curing behavior of the above system and the thermal and mechanical properties of the cured epoxy resin were studied. It was not necessary to use a curing accelerator for this system, because PHPMI caused acceleration of the curing reaction. The curing mechanism of this system was investigated by using model compounds. Test pieces from the neat resins and the glass fiber reinforced resins were evaluated in terms of thermal and mechanical properties, respectively. It was found that heat resistance and mechanical properties were improved by increasing the amount of PHPMI in the hardener.     

一个表示和运用非功能性需求的框架

本文分析了一个软件开发进程中表示和运用非功能性需求的综合框架，该框架的目的是开发一套技术以调整软件开发进程中的设计决策，从而强调了依据非功能需求，探索合理化的软件开发进程。     

钨系延期药预点火反应机理研究

通过程控升温模拟点火条件，根据ＤＳＣ图谱分析，找出主要反应区的温度范围。研究结果表明，钨系延期药预点火反应是一个真正的固－固反应。     

Geochemical approach to the Bou Hadjar hydrothermal system (NE Algeria)

The Bou Hadjar low-temperature hydrothermal system is located in northeast Algeria. The four main thermal springs that are the subject of the study emerge ith temperatures between 32 and 60°C from allochthonous formations. The reservoir temperature has been estimated from chemical compositions by utilizing simultaneously the silica, gas and sulfate-water oxygen isotope geothermometers, fluid-mineral equilibrium calculations, and a mixing model. According to these thermometric methods, the most probable subsurface temperature is in the range 75–106°C. The mixing model suggests a temperature of 125°C for the parent water.     

Early detection of ageing in solder joints through laser probe thermal analysis of the peltier effect

We have recently developed an optical contactless method for testing the quality of solder joints during accelerated thermal cycling ageing processes.¹ The method was based upon the measurement of the dynamic thermal behaviour of the joint to short bursts of Joule heating. It has proved to be efficient in revealing the formation of cracks at the lead-solder interface. We present a method to evaluate ageing at a much earlier stage in the cycling process. We have observed in earlier work,¹ that before cracks appear, structural changes occur in the solder at the lead-solder interface. The thermal response of the solder joint is recorded over time to a Peltier heat perturbation produced by flowing a current pulse through the interface where structural changes occur. The key point in this method is to discriminate the Peltier effect from the Joule thermal response because both effects generate heat. The variation of the early Peltier response in the thermal cycling ageing tests is seen as a quantitative signature of the structural changes in the lead-solder interface.     

涂硫尿素

涂硫尿素（ＳＣＵ）是一种缓效氮肥，是在普通尿素外面喷涂硫、密封剂和调理剂而制成。它在国外已成功使用多年．本文叙述了涂硫尿素的性质、生产过程、肥效和经济效益，供国内读者参考。     

Optical measurements of thermal diffusivity of a material

The measurement of thermal diffusivity of a material (in particular, a thin film) is important for various reasons, e.g., to predict the heat transfer in the solid subjected to a thermal process, to monitor surface composition or morphology, or to detect invisible subsurface defects like delaminations. This measurement can be done in a noncontact manner using various photothermal methods. Such methods typically involve pulsed heating of the surface by small amounts using a laser source; the decay of the surface temperature after this pulsed photothermal heating is then probed to provide the thermal diffusivity. Various probing methods have been developed in the literature, including the probing of reflection, refraction, and diffraction from the pulsed heated area, infrared thermal radiometry, and surface deformation. This paper provides an overview of such techniques and some examples of their applications.     

提高热采注汽系统热效率的研究

为了降低热采成本和提高经济效益 ,建立了热采注汽系统热效率的数学模型。根据实测数据计算了 9个注汽系统的热效率。提出了改进注汽系统热效率的行之有效的措施。根据排烟的氧含量的大小 ,可以确定注汽锅炉热效率改进程度 ;按管线允许热损失量和保温材料种类 ,设计保温层厚度 ,可大大提高输汽管线热效率。仅此两项 ,即可使大部分注汽系统热效率提高 7%以上 ,井底蒸汽干度提高 10 %以上。